How to Get Wires Through The Lippert Double Flexguard RV Slide-Out Kits Brackets
Question:
How do you get the wires through the the brackets on the Lippert flex guard double kit
asked by: Ronald P
Expert Reply:
The black flex guard will slide through the longer thin hole on the brackets. There is no notch to slide your wires in, so your wires will need to be disconnected on one side or the other to feed them through the holes on the brackets.
I have attached photos of the installation instructions for the Lippert Double Flexguard RV Slide-Out Kit Hardware # LC1346281.
Installation Instructions are as follows.
1. Position Flex Guard under the slide-out room where the wiring or hoses to be protected are located.
2. Insert the aluminum pin (Fig. 1A) into the Flex Guard (Fig. 1B) with the mounting bracket (Fig. 1C)
facing up. Slide the star washer (Fig. 1D) over the end of the pin at the bottom of the Flex Guard and
push in place.
3. Slide the Flex Guard clips (Fig. 1E) onto the end of the Flex Guard with the holes in the clips facing the
direction of the hoses and wiring to hold them in place. Space all clips evenly throughout the length of
the Flex Guard.
4. Install Flex Guard mounting bracket (Fig. 1C) to the bottom of the unit floor, perpendicular to the
outrigger and furthest away from the I-beam or room bar, using four #10 x 1" self-tapping screws or
#10 x 1" wood screws (Fig. 2A).
5. Mount the flat end of the Flex Guard to the LCI-supplied mounting plate (Fig. 3A) mounted offset to
the aluminum pin (Fig. 1A) at the opposite end using two #10 x 1" self-tapping screws (Fig. 3B) per belt
section. Install the LCI-supplied mounting plate to the bottom side of the slide-out room.
6. Slide any hoses and wiring through the holes in the Flex Guard clips when installing in order to protect
hoses and wiring with the Flex Guard.
7. Flex Guard should be kept parallel to the slide room floor.
8. Make sure the flat end of the Flex Guard is mounted several inches away from the direction of the bend
of the retracted Flex Guard (Fig. 4).
(click to enlarge)
(click to enlarge)
Product Page this Question was Asked From
Lippert Double Flexguard RV Slide-Out Kit Hardware
- RV Slide Out Parts
- Hardware
- Flexguard
- Lippert
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: LaSalle Bristol RV Sewer Spigot with Flange - for 1-1/2" pipe
- Shop: LaSalle Bristol RV Sewer Slip Hub with Flange - 1-1/2"
- Shop: LaSalle Bristol Waste Valve for RV Gray Water Tank - 1-1/2" Diameter - Hub to Hub
- Shop: Lippert Double Flexguard RV Slide-Out Kit Hardware
- Shop: Replacement Pull Strap for Solera Window Awning - 44"
- Search Results: 34466v1515
- Search Results: bristol valve
- Shop: Replacement Pull Strap for Solera Window Awning - 27"
- Search Results: 2022006595
- Shop: Motor Upgrade Kit for Kwikee Electric RV Steps
- Search Results: 909510000
- Search Results: lc379145
- Search Results: 2021132340
- Video: Lippert Double Flexguard RV Slide-Out Kit Hardware Review
- Q&A: Length of Lippert LC1346281 Double Flexguard RV Slide-Out Kit Wire Support
- Search Results: slide out motor
- Video: Lippert Double Flexguard RV Slide-Out Kit Hardware Installation - 2007 Starcraft Homestead Lite Fift
- Q&A: Installation of Lippert Flexguard RV Slide-Out Kit Hardware
- Shop: Suspension Enhancement
- Q&A: How to Determine Capacity of Trailer Axle with 8 Lug Wheels
- Video: Review of Valterra RV Waste Valves - Waste Valve Body With Flexible Cable - VAL22RB
- Q&A: Best 5th Wheel Hitch for 2018 Ram 2500 with Factory Puck System
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Q&A: When Will The Furrion Chill Cube RV Air Conditioner Be Aftermarket Available
- Video: Valterra RV Sewer - Connectors and Fittings - T1029-2 Review
- Article: Stability Control for Heavy Duty Vehicles
- Q&A: Will The Blue Ox Baseplate # BX1139 Fit A 2024 Jeep Wrangler Rubicon X With A Steel Bumper
on RV Slide Out Parts
