Double Lip Redline Grease Seal # 13194 Dimensions

Question

Question:

it tells the od and id what is the width

asked by: Donald D

0

Expert Reply:

Dimensions for Grease Seal # 13194

Width- 0.43"
Outer Diameter- 1.983"
Inner Diameter- 1.372"

expert reply by: Bud M

0

Answer 1

In order to determine which grease seal is the correct replacement, you will want to use a digital caliper to take measurements. A precise measurement, to the nearest thousandth, is required to ensure that the new seal will fit. The best way to…

view full answer...

Answer 2

The Bearing Buddy Bearing Protectors #BB2441 provide premium protection for your wheel bearings. It is still recommended that you inspect the bearings, races, and seals every 12 months or 12,000 miles to ensure reliable performance on your trailer.…

view full answer...

Answer 3

Thanks so much for that detailed info, and we do have the bearings, races, and grease seal that you need, which are the following: - Replacement Trailer Hub Bearing #L44649 - Replacement Race #L44610 - Replacement Trailer Hub Bearing #LM48548 -…

view full answer...

Answer 4

We can help you find the seal you need, but the part number you mentioned does not match anything we offer. Can you get me the inner and outer diameters of the seal? With that I can see what we have that matches.

view full answer...

Answer 5

Bearing Buddies like #BB2441 fit very tight into a trailer hub. In order to get them out, you will need to use a rubber mallet and persuade them out. Once the Bearing Buddy starts to unseat from the hub you can grab it and wiggle it out.

view full answer...

Answer 6

The great thing about Bearing Buddy like part #BB1781 is that when you add grease to your system with the included fitting, it will move the spring-loaded piston outward and allow grease to seep around the edges to keep from damaging the seal. You…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Double Lip Redline Grease Seal # 13194 Dimensions

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching