Is There a Replacement LED Strip Available for the Bully LED Hitch Step # CR-600LED

Question

Question:

Are replacement LED strips available? Mine has failed after several years of use and I would like to replace it.

asked by: Ron H

0

Expert Reply:

For a replacement LED light for the Bully Round Tube Stainless Steel Trailer Hitch Receiver Step, # CR-600LED, you will want the Replacement LED Light, # CR-600L-LED.

expert reply by: John H

0

Answer 1

The harness part #CR-600L-LED that you referenced is a replacement for the Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights #CR-600LED which uses a standard 4-way connection which should be present on your 2017 Chevy Silverado.…

view full answer...

Answer 2

Yes, the Pilot Replacement LED Strip #CR-600L-LED is the correct item to replace the LED lights on your Bully Black Bull LED Round Tube Hitch-Mounted Step #BBS-1104L. The kit includes the LEDs, wiring and adhesive strip.

view full answer...

Answer 3

It sounds like you have the Bully Tube Stainless Steel Trailer Hitch Receiver Step #CR-600LED and are looking for a replacement light strip for it. If so, the correct part number would be part #CR-600L-LED.

view full answer...

Answer 4

We have the Masterlock hitch lock part #1480DAT which is stainless steel that I would highly recommend. I attached a review video for you to check out as well. The replacement LED strip you need is the part #CR-600L-LED for your #CR-600LED.

view full answer...

Answer 5

To replace your wiring on your Bully hitch step #CR-600LED I recommend the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector #HM38138 along with heat shrink connectors #DW05743-5. For added protection you can add a wire loom like #7509-1 sold…

view full answer...

Answer 6

If you still have access to the four wires that run to the back of the Bully Black Bull LED Step part #BBS-1104L you can replace the 4-way with a #18004. If you do not have access to the wiring we do not have a solution for you.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 12

The best way to determine if your Explorer is equipped with the tow package is to check with your Ford dealer. They should be able to run the VIN and be able to tell you exactly how the vehicle was equipped. I'm assuming you're needing the…

view full answer...

Is There a Replacement LED Strip Available for the Bully LED Hitch Step # CR-600LED

Continue Researching