Replacement LED Light Strip Recommendation for Bully Tube Trailer Hitch Receiver Step # CR-600LED

Question

Question:

Are there replacement 24 inch red led light strips for Bully step bars and can you tell me where I can buy them? Thank You,

asked by: Steve S

0

Expert Reply:

It sounds like you have the Bully Tube Stainless Steel Trailer Hitch Receiver Step # CR-600LED and are looking for a replacement light strip for it. If so, the correct part number would be part # CR-600L-LED.

expert reply by: Jameson C

0

Answer 1

The harness part #CR-600L-LED that you referenced is a replacement for the Round Tube Stainless Steel Trailer Hitch Receiver Step with LED Lights #CR-600LED which uses a standard 4-way connection which should be present on your 2017 Chevy Silverado.…

view full answer...

Answer 2

Yes, the Pilot Replacement LED Strip #CR-600L-LED is the correct item to replace the LED lights on your Bully Black Bull LED Round Tube Hitch-Mounted Step #BBS-1104L. The kit includes the LEDs, wiring and adhesive strip.

view full answer...

Answer 3

For a replacement LED light for the Bully Round Tube Stainless Steel Trailer Hitch Receiver Step, #CR-600LED, you will want the Replacement LED Light, #CR-600L-LED.

view full answer...

Answer 4

We have the Masterlock hitch lock part #1480DAT which is stainless steel that I would highly recommend. I attached a review video for you to check out as well. The replacement LED strip you need is the part #CR-600L-LED for your #CR-600LED.

view full answer...

Answer 5

If you still have access to the four wires that run to the back of the Bully Black Bull LED Step part #BBS-1104L you can replace the 4-way with a #18004. If you do not have access to the wiring we do not have a solution for you.

view full answer...

Answer 6

To replace your wiring on your Bully hitch step #CR-600LED I recommend the Hopkins Wiring Harness with 4-Pole Flat Trailer Connector #HM38138 along with heat shrink connectors #DW05743-5. For added protection you can add a wire loom like #7509-1 sold…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Hey Antoine, so the two kits you mentioned are actually really similar and honestly I would go with the part #ETBC7 if I were you. The #ETBC7L is basically the same thing minus a couple wires and breakers so you may as well get the kit that has…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The best way to determine if your Explorer is equipped with the tow package is to check with your Ford dealer. They should be able to run the VIN and be able to tell you exactly how the vehicle was equipped. I'm assuming you're needing the…

view full answer...

Answer 12

I recommend the Fastway e2 Weight Distribution #FA92-00-0800 for your 2022/2023 Coleman 17B travel trailer. This hitch is rated for a tongue weight of 400-800lbs and a maximum trailer weight of 8,000lbs. With a dry tongue weight of 385lbs by the time…

view full answer...

Replacement LED Light Strip Recommendation for Bully Tube Trailer Hitch Receiver Step # CR-600LED

Continue Researching