Needing 3500 lb Hub/Drum With 5 on 5 Bolt Pattern
Question:
I read your parts needed for 3500 trailer. My trailer specs BigTex 35SB states: AXLE 3,500# EZ Lube Axle w/ Brake Flanges with WHEEL 15 x 5 Black Spoke, 5 on 5 Bolt Pattern. What hub would I need so I dont have to buy new wheels and tires? I assume the hub listed in the article that state 5 on 4 1/2 will not fit.
asked by: Mark
Expert Reply:
You're correct, a hub/drum with a 5 on 4-1/2 inch bolt pattern wouldn't be compatible with your existing wheels.
For a hub/drum for a 3500 lb axle with a 5 on 5 bolt pattern, I'd recommend the # AKHD-550-35-EZ-K. This hub/drum is compatible with the spindles typically found on a 3500 lb axle, which uses a L68149 inner and L44649 outer bearing and a 58846 grease seal. The hub includes the inner and outer bearings, inner and outer races, the grease seal, dust caps for a standard and E-Z lube spindle and lug nuts. The hub/drum is fully greased and is ready to install. The hub would be fully compatible with your existing 15 inch wheels.
For brake assemblies, I'd recommend self-adjusting brakes like # AKEBRK-35L-SA for the left side and
# AKEBRK-35R-SA for the right. If you don't wish to reuse your existing brake mounting hardware, we offer replacement hardware as part # BRKH10BS.
I'll link to an article showing how to install the hub and brake assemblies.
Products Referenced in This Question
Electric Trailer Brake Assembly - Self-Adjusting - 10" - Left Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- LH
- 3500 lbs
- Brake Assembly
- Self Adjust
- 10 x 2-1/4 Inch Drum
- etrailer
more information >
Electric Trailer Brake Assembly - Self-Adjusting - 10" - Right Hand - 3,500 lbs
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- RH
- 3500 lbs
- Brake Assembly
- Self Adjust
- 10 x 2-1/4 Inch Drum
- etrailer
more information >
Easy Grease Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 5 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 5 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Mounting Hardware for 10" Single Brake Assembly
- Accessories and Parts
- Trailer Brakes
- Electric Drum Brakes
- Hydraulic Drum Brakes
- Hardware
- 10 Inch
- Redline
more information >
Product Page this Question was Asked From
Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Trailer Hubs and Drums
- Hub with Integrated Drum
- Easy Grease
- EZ Lube
- Pre-Greased
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 4-1/2 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Continue Researching
- Article: Top Gifts for Dads in 2024
- Q&A: How To Tell If Bearing Buddy Has Enough Grease
- Q&A: How Does Lippert Components Spare Tire Winch with Offset Cable Crank Up and Down
- Q&A: Weight Capacity Of Lippert Spare Tire Winch For Over sized Tire
- Q&A: Inside Diameter of Replacement Crank Extension for Lippert Spare Tire Winch Assemblies
- Q&A: How is Lippert Spare Tire Winch LC159056 Raised and Lowered
- Q&A: Does Lippert Spare Tire Winch Lock or Hold in Any Position?
- Q&A: Can Bearing Buddy Bearing Protectors Be Over-Filled with Too Much Grease
- Article: Trailer Wiring Diagrams
- Article: Testing Trailer Brake Magnets for Proper Function
- Article: Most Popular Wheel Bearings
- Article: How to Charge a Dump Trailer Battery
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: Best RV Roof Vents