Is There a Replacement Base Available for the Demco Recon?

Question

Question:

I already have the Demco for recessed balls, item#: DM8550046. I would like to order just the base plate for Item # DM8550045, because I already have the post and head.

asked by: Kevin C

0

Expert Reply:

We do have the Replacement Base Assembly for Demco Recon # DM6201, but this will include the post. Demco currently does not offer the base without the post

expert reply by: Lazer S

0

Answer 1

The foot print of the Demco Recon fifth wheel adapter #DM8550045 which is the base of the Recon Hitch part #DM6201 is 28” front to back and 30.5” left to right. Looks like you'd be an inch short as this would have 14 inches forward and rear of…

view full answer...

Answer 2

The Demco UMS Double Pivot 5th Wheel Hitch #DM47GV is our highest capacity 5th wheel hitch at 31,000lbs that will fit into the factory prep/puck system on your 2022 Chevrolet Silverado 3500 dually with an 8' long bed. I recommend using a Lube…

view full answer...

Answer 3

While both 30k 5th wheel hitches that fit the puck system of your 2023 Chevy Silverado 3500 have high-quality jaw systems, between the Curt PowerRide #C36WR and Demco UMS Double Pivot #DM47GV, the better jaw system is on the latter, the Demco UMS…

view full answer...

Answer 4

Yes, the Replacement Base Assembly for Demco Recon Gooseneck-to-5th Wheel Trailer Hitch Adapter #DM6316 is specifically designed for flatbeds that have 2-5/16" recessed gooseneck hitch ball. Just keep in mind that the top of the gooseneck ball…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 11

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...