Dimensions of Buyers Products Hitch Plate part # 3371809065

Question

Question:

What is the length width and hight ?

asked by: Yll

0

Expert Reply:

I checked with Buyers Products and the overall length of the Hitch Plate part # 3371809065 is 62 inches, height is 17 inches and width is 7-1/4 inch. The weight is 102 lbs.

expert reply by: Jameson C

0

Dimensions
(click to enlarge)

Answer 1

The overall dimensions for the Buyers Products Pintle Hitch Plate w/ ICC Bumper for Chevy/GM 3500 Cab and Chassis #3371809035A are 63" wide x 15.5" tall x 3" deep. If you need any other measurements just let me know.

view full answer...

Answer 2

If your 2008 Chevy Silverado initially came with the cab and chassis body then you should be able to use the Buyers Products Hitch Plate with Receiver Tube - Chevy/GMC #3371809065. This is for the 3500 model and measures 17" tall by…

view full answer...

Answer 3

The width of the tab you marked in your picture is 2.9" and the height is 6.32". I have attached the full dimensional drawing of the #3371809065 below for your reference.

view full answer...

Answer 4

The side plates in the Curt Class 5 Universal Weld-on Hitch #C87CR have only been tested by Curt in the vertical position. With that they are not sure how the mounting brackets will hold up if mounted horizontally. I recommend the Buyers Products…

view full answer...

Answer 5

I would be happy to help you with that. I went out to the warehouse and took some measurements of the Buyers Products Hitch Plate with Receiver Tube - Chevy/GMC item #3371809065. The distance between the two wings on the top outside edge of the hitch…

view full answer...

Answer 6

As long as the distance from outside to outside on the rear frame rails of your 1973 Chevrolet T-65 is 34 inches the Buyers Products Hitch Plate with Receiver Tube #3371809065 is the correct size and would work well. It's designed to fit the…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Thanks for reaching out, Adam! The Buyers Products Hitch Plate with 2" Receiver Tube #3371809060A is designed to fit a Ford chassis, and all of the other HD hitches like this from Buyers Products. For your application you need a universal hitch…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Dimensions of Buyers Products Hitch Plate part # 3371809065

Product Page this Question was Asked From

Continue Researching