TorkLift 36 Inch Hitch Extender for Ford Factory 3 Inch Receiver Hitch

Question

Question:

Would this work with a model year 2016 that also has 3inch factory receiver?

asked by: Roderick W

0

Expert Reply:

I am a bit confused, because I was under the impression that Ford didn't begin offering the 3 inch hitch until the 2017 model year.

As long as the hitch on your 2016 Ford truck is the 3 inch factory receiver, the Torklift # TLE1636 will be compatible.

if you need an extension for the 7-way trailer connector, use part # TLW6036.

expert reply by: Mike L

0

Answer 1

In the 3 inch hitch version the shortest version of the Cannon Ford Hitch Extension is the part #TLE1636 which is 36 inches long.

view full answer...

Answer 2

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors…

view full answer...

Answer 3

The best air bag kit for your 2022 Ford F-350 that has a single rear wheel axle is the part #F95FV which has the 5,000 lb capacity you are wanting. Firestone bags are superior Air Lift bags. The ply rating of the rubber is higher, the attachment to…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 5

With the weight of your camper I recommend the Air Lift LoadLifter 5000 Ultimate Air Helper Springs #AL35FJ. I prefer these as they have the internal jounce bumper which helps to reduce the bounce that is often associated with towing a trailer and…

view full answer...

Answer 6

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

The Torklift Hitch Extension part #TLE1636 that you referenced can tow a trailer that weighs 6,700 lbs like you what you have but you would need to use a weight distribution system with it to have the needed capacity as without a WD system it's…

view full answer...

Answer 9

Since you are pulling a trailer that weighs around 8,500 lbs. you would just want to stick with the Firestone Ride-Rite Air Helper Springs #F35FV (5,000 lb.). You really only need to spend more for the Firestone Ride-Rite Red Label Extreme Duty Air…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you have the Ford 3" hitch then you can definitely add it but, yes it would change the weight capacity. The TorkLift Cannon Hitch Extension item #TLE1636 only has a 3,600 lbs towing capacity and a 360 lbs maximum tongue weight. If used with a…

view full answer...

Answer 12

Yes, you can replace your current Lippert Equa-Flex equalizers with the MORryde AllTrek 4000 Equalizers #MR29DR on your 2018 Highland Open Range. The yellow octagons on the front and rear are a for correcting the alignment of the axles and are not…

view full answer...

TorkLift 36 Inch Hitch Extender for Ford Factory 3 Inch Receiver Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching