Replacement Metal Roof Vent For A 14" x 14" Vent

Question

Question:

2018 puma travel trailer, replacement roof vent cover number is 4140155 will the metal ones you have fit ours Part number BV0534-00

asked by: Lori

0

Expert Reply:

If you have a cover like the part number 4140155 that you have provided, that is a 14" x 14" so this low profile metal cover # BV0534-00 is 14-1/4" by 14-1/4". The extra 1/4" is just from the 1/8" lips on each side.

expert reply by: Adam E

0

Answer 1

Replacement vent covers are very specific in terms of what vents they will fit. Metal cover #BV0534-00 is designed to fit Ventline Ventadome roof vent model V2110. If your vent originally had a plastic cover chances are this metal one will not fit. I…

view full answer...

Answer 2

The only metal roof vent cover we offer is Replacement Dome Assembly #BV0534-00 which has a continuous hinge and fits a 14 x 14 inch roof vent. Since the hole in your existing vent is 14 x 14, you will want to check if your previous vent cover had a…

view full answer...

Answer 3

You can replace your plastic vent cover #BV0554-01 with the metal lid part #BV0534-00 that you referenced and you'd be set.

view full answer...

Answer 4

When measuring for a replacement vent lid, you will want the outside dimension of the housing that extends through the trailer roof. This dimension is typically 14 by 14 inches. Closely examine the remaining portion of the vent, looking for a…

view full answer...

Answer 5

Yes, if you have the same continous hinge on your roof vent as the metal lid part #BV0534-00 this lid will work well as a replacement. I attached an install video for this for you to check out as well.

view full answer...

Answer 6

Generally speaking, if the hinge is the same then you can use pretty much any replacement lid as the sizes are all standard. Therefore, the metal Replacement Dome Assembly for Ventline Ventadome Trailer Roof Vent part #BV0534-00 should work for you…

view full answer...

Answer 7

If the roof vent on your horse trailer is the standard size of 14 inch by 14 inch then yes the Ventline Roof Vent part #BV0534-00 is a fit and would work well. If the vent you are replacing happens to be smaller you could always enlarge the hole to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...

Replacement Metal Roof Vent For A 14" x 14" Vent

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching