Can I Use Weight Distribution Shank for BulletProof Hitches with Equal-I-Zer Hitch

Question

Question:

Will this adaptor fit the 12k equalizer wd system ,I already have the bullet proof hitch

asked by: Joe N

0

Expert Reply:

Yes. The Weight Distribution Shank for BulletProof Hitches Adjustable Ball Mount # 358WEIGHTDIST can be used with an Equal-i-zer weight distribution system like the # EQ37140ET since the holes on the shank are spaced 1-1/4" apart. This will work well with your Bulletproof Hitch.

expert reply by: Erik B

0

Answer 1

While it is uncertain if or when someone will make a weight distribution shank for a 3" Ford Receiver, I have seen where a BulletProof Hitches Adjustable 2-Ball Mount #HD308 is used with the Weight Distribution Shank for BulletProof Hitches…

view full answer...

Answer 2

Yes. The Replacement Head for Curt MV Weight Distribution Systems #C17075 you were looking at will fit perfectly on the Weight Distribution Shank for BulletProof Hitches Adjustable Ball Mount #358WEIGHTDIST you purchased. This will allow you to use…

view full answer...

Answer 3

The Ford OEM puck system is different than the Chevrolet/GMC OEM puck system therefore, you can't use a 5th wheel hitch from one in the other. The Ford OEM system has pucks which are much closer together than on the Chevrolet/GMC OEM system. The…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Robin, Yes, you can absolutely use the 2" Equal-i-zer Weight Distribution Shank #EQ90-02-4600 with the Blue Ox SwayPro Weight Distribution #BXW2000. The hole spacing on the Equal-i-zer shank is the same as the Blue Ox shank which is why they…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

Whether or not you can flat tow with a Jeep bumper is really up to the manufacturers testing; some of the big names like MetalCloak or Poison Spyder have bumpers with D-ring attachments that can be used for flat towing connections. This is great…

view full answer...

Answer 11

Your 2024 Chevrolet Silverado 3500 will come with a 2-1/2" trailer hitch receiver. If your truck did not come with a reducer for a 2" receiver we do have the B&W #BWRHXA2182 if you need to use your 2" ball mount or hitch mounted…

view full answer...

Can I Use Weight Distribution Shank for BulletProof Hitches with Equal-I-Zer Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching