What Is The Tongue Weight and Trailer Weight Rating Of The Draw-Tite Trailer Hitch 75270?
Question:
I noticed on the product info that the tongue weight for a non WD configuration is listed as 675# and 350# depending on where you look. Which is the correct tongue weight? I am planning to mount on a 2013 Honda Odyssey EX-L. Compared with the other two visible crossbar options, #75270 would have a much higher tongue weight if 675# is correct. Thank you
asked by: Eric
Expert Reply:
The Draw-Tite Trailer Hitch Receiver # 75270 you were looking at for your 2013 Honda Odyssey EX-L does in fact have a 675lb tongue weight rating and 4500lb trailer weight rating which I confirmed with Draw-Tite. Our website has been updated to only show this rating.
You are correct that this is significantly higher than the other trailer hitch receivers offered for your Odyssey, which is why I recommend it for your vehicle.
If you are planning on towing with your vehicle you will also need a vehicle wiring harness # 118521, and a hitch ball, ball mount, and hitch pin and clip which can all be found in the etrailer Ball Mount Kit # 989900.
I included installation videos for each of the products mentioned for you to take a look at.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 675 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Trailer Hitch
- Article: How to Choose the Right Trailer Hitch Class
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: My Trailer Hitch Doesn't Fit
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Q&A: Recommended Hitch for VelociRAX 5 Bike Rack on 2012 Honda Odyssey
- Article: How to Clean Weld Nuts for the Installation of a Trailer Hitch | etrailer.com
- Q&A: Comparison Between Draw-Tite 76025 and EcoHitch 306-X7253 for 2015 Honda Odyssey
- Article: How to Measure for Trailer Hitch Drop
- Article: Trailer Wiring Diagrams
- Article: Transmission Cooler
- Q&A: Choosing OEM or Aftermarket 5th Wheel Puck System for 2021 Ford F-250
- Q&A: How To Install a 7-Way Trailer Connector On a 2016 Honda Odyssey
- Q&A: Honda Odyssey Custom Built Class III Round Tube Trailer Hitch Bolt Sizes
- Q&A: Solution for Keeping RV Furrion Refrigerator Doors Closed when Travelling