What is the Outer Dimension of the Flange Body

Question

Question:

Hi there. At about minute 0:33 in your video, you say that the outer diameter of the flange face is 16.25inch and the internal diameter is 13.5. What is the outer diameter of the flange body? Is it meant to fit through a 14inch x 14inch square cut out?

asked by: Keith B

0

Expert Reply:

The Ceiling Garnish for MaxxAir Maxxfan RV Roof Vent - Black # MA10-20209 is designed to fit in 14" x 14" rough vent cutout dimensions and the plastic garnish itself is roughly 1/4" thick. The outer diameter of the flange body will be 14" x 14".

expert reply by: Erik B

0

Answer 1

It sounds like you're looking for the Ceiling Garnish for MaxxAir Maxxfan RV Roof Vent #MA54FR, and will fit a standard vent opening of 14" x 14".

view full answer...

Answer 2

When it comes to trimming The Ceiling Garnish for MaxxAir MaxxFan RV Roof Vent #MA54FR you will need to use masking tape to mark where you want to make your cut on the garnish. You will then need to use a hand saw to cut along the masking tape. I…

view full answer...

Answer 3

The ceiling garnishes like the MaxxAir Maxxfan RV Roof Vent - White item #MA54FR you were looking at are universal. So long as you have the standard 14"x14" opening for your MaxxAir 4501k this garnish will be able to fit. It may…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

What is the Outer Dimension of the Flange Body

Product Page this Question was Asked From

Continue Researching