Does Happijac Tie Downs part # LC182906-182971 fit 2006 Chevy Silverado 2500HD

Question

Question:

Advise whether item in fact does fit my truck, a 2006 Chevrolet Silverado C2500Hd extended cab with 6.5foot bed, 2wd, oem hitch, 8foot rear frame rails.

asked by: Wayne L

0

Expert Reply:

Yes the Happijac tie downs part # LC182906-182971 are a confirmed fit for your 2006 Chevy Silverado 2500HD with an extended cab with an OEM hitch.

expert reply by: Jameson C

0

Answer 1

The HappiJac Camper Tie-Downs #LC182906-182971 that fits your 2023 Chevy Silverado 2500 can be pieced out with the Replacement Front Anchor Plates #LC182872 being what you've referenced needing.

view full answer...

Answer 2

We do carry Torklift brand tie downs for your 2004 Chevy Silverado that attach to the truck frame but I would need more info from you to pick them out. What is your bed length? Do you have running boards? Factory hitch?

view full answer...

Answer 3

For your 2019 Chevrolet Silverado 1500 LD, the HappiJac Truck-Mounted Camper Tie-Downs we carry are sold as a complete package. I recommend the HappiJac part number #LC350763-182971 for a 6-1/2' bed. This is a different part number than what you…

view full answer...

Answer 4

You do not need to remove the bed of your truck to install the HappiJac part #LC182906-182971 that you referenced. I found a copy of the install instructions for this part number (see attached pictures) and there's no mention of the bed needing…

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 11

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 12

You'll need to do some slight measuring to ensure the fit of the Firestone Ride-Rite Red Label Extreme Duty Air Helper Springs #F95FV on your 4WD 2022 Ford F-350 FX4 dually. Just measure from the top of the rear axle to the top of the jounce…

view full answer...

Does Happijac Tie Downs part # LC182906-182971 fit 2006 Chevy Silverado 2500HD

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching