Correct Replacement Leaf Springs for Trailer with Dexter 3,500 Lb Axle

Question

Question:

I need replacement springs for 2016 Northwood Nash 23D 3500 lb. Dexter axel..

asked by: Scott L

0

Expert Reply:

In order to find the correct replacement leaf springs for a trailer you'll need to know the type (slipper/double eye), weight capacity, and unloaded length. The springs will stretch over time so the new replacements will be shorter. If you have a 3,500 lb axle with double eye springs then you'll likely need 3-Leaf Double-Eye Spring part # e59SR which measure 23-1/8" long.

expert reply by: Conner L

0

Answer 1

Yes you can use the Dexter EZ-Flex cushioned equalizer part #K71-652-00 on your 2014 Nash 23D trailer that has a 31 inch axle spacing.

view full answer...

Answer 2

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 3

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 6

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 7

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 8

Yes, going from a 4 leaf to a 6 leaf spring would add slightly to your ride height. For example, if the current 4 leaf spring has 3/8" thick leaves, and you go to a 6 leaf spring with 3/8" thick leaves, you would be adding 3/4" of…

view full answer...

Answer 9

Hey Patrick, so for your leaf spring upgrade I am going to need to know a couple of things before I can get you over to the right part. Specifically, the length from eye to eye, the spring width, leaf thickness, and the number of leaves. From here I…

view full answer...

Answer 10

Hi Bruce, To lift your trailer we'll first need to check of the suspension and see if you have torsion axles or a leaf spring suspension. If you have torsion axles then I'll need to see the axle tag in order to determine what you have so I…

view full answer...

Answer 11

When replacing shackle straps they should be the same length as the ones that were previously on your tandem axle trailer; replacing them with longer straps will result in additional play in your trailer suspension which could lead to additional wear…

view full answer...

Answer 12

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Correct Replacement Leaf Springs for Trailer with Dexter 3,500 Lb Axle

Product Page this Question was Asked From

Continue Researching