Brophy Clamp On Camper Tie-Down Placement

Question

Question:

Is this the one to use, even if running boards stop at end of cab?

asked by: Kim

1

Helpful Expert Reply:

The Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item # HSAB mount to the bed rail instead so you won't have any space issues with the running boards of your truck.

expert reply by: Kevin C

1

Answer 1

Brophy tie downs, #HSSF, do not have an official fit list but they tend to not work well on import trucks like your 2011 Nissan Frontier. They do offer a different style that clamps on, #HSCP, that is more likely to fit as long as the truck bed is…

view full answer...

Answer 2

For a more economical option we have the Brophy camper tie downs, but they are not frame mounted. They are bed mounted. The Brophy Camper Tie Downs, part #TDSF, are a universal application for full-size trucks and they will fit your Ram 1500. The…

view full answer...

Answer 3

The Brophy #HSAB are designed to be a universal fit on most trucks; as long as your bed rails aren't wider than 5-1/2" then you'll be able to use these camper tie downs on your 2008 Frontier without any issues. These are a nice solution…

view full answer...

Answer 4

I attached a picture that shows the instructions we have for the Tie Downs part #HSAB that you referenced. We've haven't seen them be an issue on a 2001 Ford F-150, but if you could get me a picture of what your setup looks like I can see if…

view full answer...

Answer 5

The Brophy camper tie downs #HSAB are pretty universal and should fit your 1997 Chevy K1500 pretty easily but you might measure the bed rails just to be sure. As long as you have 2 inches of space between the lip of the bed rails and the side of the…

view full answer...

Answer 6

Yes, the Brophy camper tie downs like the #HSAB can be used with bed rail covers. If you check out the picture I attached you can see a set installed on a bed rail with plastic covers.

view full answer...

Answer 7

The reason the manufacturers of the Brophy Clamp On Camper Tie-Downs - Bed Mount - Black Powder Coated Steel - Qty 4 Item #HSAB have the plastic bed rail exemption is because depending on the thickness of the plastic bed rail you might not have…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 12

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Brophy Clamp On Camper Tie-Down Placement

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching