Does The Replacement Tie-Down # EX1024 for the Solid Fold 2.0 Include Mounting Hardware?

Question

Question:

Does the product come with the mounting screws? Or is that a separate item? If separate which part item do you need to secure the replacement straps and clip

asked by: Matt

0

Expert Reply:

The Replacement Tie-Down # EX1024 for the Solid Fold 2.0 does not include mounting hardware. If you cannot use your current screws you will need to source four of the 8-18 x 5/8 PFH TEK #2 screws locally for replacements.

expert reply by: Bud M

0

Answer 1

Thanks for the picture! Wthout knowing for sure what model tonneau cover you have, I can't say for sure. However, it does look like this strap will be compatible with your tonneau cover. As long as you have the 83-XXX series Extang Solid Fold 2.0…

view full answer...

Answer 2

The Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers - Qty 1 #EX1024 that you were looking at measures 1-3/4" between bolt holes on the strap's tie-down and measures 1-1/4" between bolt holes on the clip. I attached…

view full answer...

Answer 3

First you will need to determine if you have the Extang Solid Fold 1 or 2.0 on your 2014 Ford F-150, as the update occurred right at the same timeframe your F-150 was made. The best way to tell the difference is by the release handles on the tailgate…

view full answer...

Answer 4

The Replacement Female Tie-Down Buckle for Extang SolidFold Tonneau Covers #EX1018 is the only way to get the buckle for the original Extang SolidFold covers. We do have the Replacement Female Tie-Down Buckle for Extang SolidFold 2.0 Tonneau Covers…

view full answer...

Answer 5

No, the Replacement Tie-Down for Extang Solid Fold 2.0 Hard Tonneau Covers #EX1024 will not fit all makes of tonneau covers. They are specifically a fit for the Extang Solid Fold 2.0 83 series covers. But, we have had some other models from Extang…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Does The Replacement Tie-Down # EX1024 for the Solid Fold 2.0 Include Mounting Hardware?

Product Page this Question was Asked From

Continue Researching