Does Trailair Flex Air Pin Box Have Pin Weight Capacity

Question

Question:

Is hitch weight a factor with this pin box? I didnt see any information on that. I have a 2021 Fuzion 428.

asked by: Jason D

0

Expert Reply:

As long as the total weight of you 2021 Fusion 428 is less than 21,000 lbs the Lippert Flex Air # LC369535 would work well. It doesn't have a pin weight capacity listed but as long as the total trailer weight is less than 21,000 lbs the pin weight would be fine.

expert reply by: Jameson C

0

Answer 1

It sounds like you need to re-calibrate the zero point on your Lippert Ground Control 3.0 #LC304136 system. Below I've listed out the steps you'll need to follow and will allow you to use the auto leveling again. Zero Point…

view full answer...

Answer 2

I've seen the Trailer Saver before, it looks like a great hitch but we don't have any personal experience with it. I've done some research though, and I can certainly see how a flexible linkage between the hitch and vehicle (air bags on…

view full answer...

Answer 3

The psi inside the Trailair Flex Air 5th Wheel Pin Box part #LC369535 varies by application so we cannot provide an exact amount but the range is 20 psi to 120 psi and most will be between 70 psi and 100 psi. The sticker was recently replaced with a…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 6

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 10

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 11

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Does Trailair Flex Air Pin Box Have Pin Weight Capacity

Product Page this Question was Asked From

Continue Researching