What Is The Overall Length Of The Replacement Crank Handle For Etrailer 5th Wheel Landing Gear?

Question

Question:

What is the overall length of the RVLG-HDL

asked by: David G

1

Helpful Expert Reply:

The Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear # RVLG-HDL measures 31" long, including the handle on the end. The crank assembly itself measures 27" not including the handle on the end. I attached a photo diagram along with a demonstration video for you.

expert reply by: Andrew N

1

Dimensions Of Replacement Crank Handle For 5th Wheel Landing Gear
(click to enlarge)

Answer 1

The retracted height of this product #BD0287600300 is 29-1/2", the ball hole is 2-5/16", and has a range of adjustment of 8".

view full answer...

Answer 2

The gearbox on the Landing Gear Set part #RVLG-8000 can be rotated 90 degrees so that the drive shaft is positioned in front of the leg. That said, you will need to make sure you have adequate clearance to make a full rotation on the handle. The…

view full answer...

Answer 3

I actually like your first idea better because we have trailer vents that you can install on your door to help keep water spray away from the internal components. Our selection ranges from battery box vents like part #A10-3300BK-05 to ventilator…

view full answer...

Answer 4

Turning the wheel so that the teeth on the wheel move upward will expand the brake shoes against the inside of the brake drums. Moving the teeth downward will contract the brake shoes. You can see the adjustment procedure by clicking on the video…

view full answer...

Answer 5

It seems like you have the ADTH 1RV-200 Motor which has a capacity of 6,500 lbs. You can use this replacement motor #LC142178 which has a 4" on center mounting hole spacing. This one is a bit heavier duty than your other which could prevent it…

view full answer...

Answer 6

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 7

I don't have any way of determining if the Replacement Crank Handle for etrailer and Ram 5th Wheel Landing Gear #RVLG-HDL will work with your 2007 Fleetwood Nitrous Hyperlite TT Toy Hauler or not, unfortunately. The Replacement Crank Handle…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

What Is The Overall Length Of The Replacement Crank Handle For Etrailer 5th Wheel Landing Gear?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching