Replacement Pivot Arms for B&W Patriot16k Hitch

Question

Question:

i have noticed one of my pivot arms has a crack in it, can i get the pivot arms replaced?

asked by: Richard P

0

Expert Reply:

The pivot arms for your B&W # BWRVK3200 are not sold separately. You would need to replace the base with B&W # BWRVB3200 base. However you should first call B&W to determine if this is covered under their warranty.

expert reply by: Les D

0

Answer 1

If you already have a Companion hitch head then all you would need is the part #BWRVB3055 to use your current head on your flat bed truck. If you don't have a Companion already you would instead need the part #BWRVK3050 as it comes with the head…

view full answer...

Answer 2

Having the head of a B and W Companion like the #BWRVK3500 positioned with the pivot arms in the middle most horizontal and vertical setting would give you the most neutral position that should work the best for most trailers under most…

view full answer...

Answer 3

I attached a picture that I took from the install instructions that shows all of the components that comes with the B and W Companion Hitch part #BWRVK3500. Basically it comes with everything needed to completely assembly and install into a B and W…

view full answer...

Answer 4

The base part #BWRVB3055 measures 18 inches wide by 18 inches long and is designed to mount in an opening that measures 20 inch by 20 inch. The B&W Companion Flatbed Gooseneck-to-5th-Wheel Trailer Hitch Adapter #BWRVK3050 is what this is the base…

view full answer...

Answer 5

The feet of the base should be sitting flush with the top of the gooseneck ball opening. Looking at the CM AL SK it you have a recessed area for the gooseneck hitch so the #BWRVB3055 will have to fit down inside there. The base is an 18" x…

view full answer...

Answer 6

All of the B&W Companion heads are the same, so if you change to another Companion base, it will be compatible. In other words, you can definitely use your existing Companion head with the Replacement Base for B&W Companion Flatbed 5th Wheel…

view full answer...

Answer 7

The replacement pin box for a Leland 7920 or 7921 we offer is the 5th Airborne Premium Fifth Wheel Air-Ride Coupler with SIdewinder #ST400-5AS16K. This pin box reduces chucking by almost 60 percent and helps relieve stress on the coach frame while…

view full answer...

Answer 8

The Lippert/Trailair pin box that fits the Leland 7920 is #UF35-946208.

view full answer...

Answer 9

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter #AM3200 is 24 inches long by 24 inches wide and will sit 12.5 inches above the bed rails. When you add the hitch ball, it will be 15.75 inches, 16.875 inches, or 18 inches…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Replacement Pivot Arms for B&W Patriot16k Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching