Recommended Air Bag and Compressor System for 2021 Toyota Tacoma

Question

Question:

price for overload air overload and compresser to adjust from cab

asked by: Donna

0

Expert Reply:

I recommend using the Firestone Ride-Rite Air Helper Springs - Double Convoluted - Rear Axle # F2407, which are the only confirmed air bag currently available for a 2021 Toyota Tacoma. To add a compressor system I recommend using the Firestone Dual Air Command # F49VV. This is a dual path system that will allow you to inflate the air bags independently to different pressures, which can help with off-center loads in the truck bed.

expert reply by: Erik B

0

Answer 1

The Firestone #F2410 will fit the leaf under axle style set up for the 2020 Toyota Tacoma. For the leaf over axle style set up, you will need the Firestone #F2407. Though they are very similar, the brackets are different to accommodate this…

view full answer...

Answer 2

The suspension enhancement 2019 Toyota Tacoma I recommend the the Firestone Ride-Rite Air Helper Springs #F2407 because they will help reduce the sag in your truck when towing and will benefit your Tacoma even when you are not towing by reducing the…

view full answer...

Answer 3

The air springs used in Firestone Ride-Rite kit #F2407 for your 2011 Toyota Tacoma Pre Runner have a maximum diameter of 6.60 inches. They will be centered on the leaf spring stack. The lower bracket will be offset closer to the wheel. The upper…

view full answer...

Answer 4

Yes, the Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 can install and be used with your existing tailgate lock you have from Pop and Lock. It ties into the same circuits your tailgate lock ties into so you…

view full answer...

Answer 5

The Pop & Lock Power Lock Conversion Kit for Truck Caps and Hard Tonneau Covers #PAL9772 will work on the A.R.E. MX series truck cap you referenced on your 2017 Ford F-250 Crew Cab Short Bed. This will give you a clean look along with the keyless…

view full answer...

Answer 6

The correct lock and unlock wires to splice into on a 2016-2019 GMC Sierra to install the Pop & Lock Power Locking Handle for Truck Caps and Hard Tonneau Covers part #PAL9555 should be a tan with a yellow stripe and grey. That said, it is always…

view full answer...

Answer 7

I reached out to my contact at Pop & Lock and sent him along the picture you attached of the latch on your Leer camper shell. He said based on the image the Pop & Lock Power Locking Handle #PAL9555 should work perfectly. The only reason I use…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...