Will The Titan Brake Actuator T4750520 Work With Titan Disc Brake Assembly THRCM13378DACEK

Question

Question:

I was wondering if Titan Brake Actuator w/ Electric Lockout - Painted - Disc - 2-5/16inch Ball - 20,000 lbs Item # T4750520 will work with Titan Disc Brake Assembly - 13inch Hub/Rotor - 8 on 6-1/2 - Dacromet - 7,000 lbs Item # THRCM13378DACEK? Or do I have the buy HydraStar Electric Over Hydraulic Actuator for Disc Brakes - 1,600 psi Item # HBA16?

asked by: James V

0

Expert Reply:

For a surge style set up, the Titan Disc Brake Actuator # T4750520 will definitely be a good actuator. This will also work in unison with the Titan Disc Brake Assembly # THRCM13378DACEK without issues. This does utilize an electric lockout making backing up a lot easier as well.

If you wanted to go with an electric over hydraulic set up, the HydraStar # HBA16 would be a great option. That being said, to activate an electric over hydraulic actuator, you will need a brake controller like the Tekonsha Prodigy P3 # 90195. You will also need to have a 7 Way completely wired to the back of the vehicle. If you do not, our Universal Installation Kit for Electric Brake Controllers # ETBC7 will need to be installed.

Though the # HBA16 paired with a brake controller will be more interactive while towing, the # T4750520 will require less fussing and is far simpler to set up and use.

expert reply by: Lazer S

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 3

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 5

Thank you for the pictures! For a replacement option I recommend the Dexter DX7.5L A-60 Brake Actuator w Electric Lockout - Bolt On - Disc - 2" Ball - Zinc - 7.5K #DX29FR to replace your current actuator. The #DX29FR has a 7500lb trailer weight…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The "KTC 7600" stamped on the brake pad doesn't look to be a part number, so I can't cross reference it, but we do know you have Kodiak ceramic brake pads. So to determine the correct brake pads, all you need to do is match up…

view full answer...

Answer 9

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

The Dexter 8-427 hub is no longer available. Even looking through Dexter's site the only references to it are replacement bearings. You can use a wheel with a larger pilot hole as long as the wheel attaches to the hub using lug nuts and not…

view full answer...

Will The Titan Brake Actuator T4750520 Work With Titan Disc Brake Assembly THRCM13378DACEK

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching