Troubleshooting Flashing Yellow Lights of Lippert Ground Control

Question

Question:

My Jacks won’t go up. All yellow lights are flashing at the same time. What should I do

asked by: Theodore

0

Expert Reply:

When all of the yellow lights of a Lippert Ground Control display are flashing that would indicate you'd need to reset the module. To do that you have to hold down the four direction buttons for at least 5 seconds. If that doesn't fix the issue you'd have to replace the module with the part # LC304136 that you referenced.

expert reply by: Jameson C

0

Answer 1

The correct replacement circuit and control board for your Lippert Electronic leveling system is the Replacement Control Panel for Lippert Ground Control 3.0 and Travel Trailer RV Leveling System #LC421484. This will be a plug and play solution, so…

view full answer...

Answer 2

It appears that all you going to need is the Replacement Lippert 4-Point Leveling System Control Brain Wiring Harness #LC178278. This wiring harness will allow you to plug your new Replacement Lippert Leveling Control Brain for 4-Point Leveling…

view full answer...

Answer 3

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the…

view full answer...

Answer 4

I reached out to my contact at Lippert and they said that it sounds like you just aren't holding the 4 buttons for the reset long enough. It requires 5 seconds, but many people will count to 5 a little too fast and the system won't reset. He…

view full answer...

Answer 5

I checked with Lippert and they gave me the following instructions for your Ultra Level to clear the code you have: In order clear this error, press and hold all 4 directional buttons as once for 3-5 seconds. If this error comes back, check fluid…

view full answer...

Answer 6

The replacement Lippert Horizontal Power Unit Hydraulic Leveling kit #LC56FR has a 7 quart capacity. This is specifically for the Lippert Towable Level-Up system.

view full answer...

Answer 7

I have attached some diagrams of the wiring for the Lippert Replacement Hydraulic Power Unit with 2-Quart Pump Reservoir Kit for RV Slide-Out IRC System #LC141111. The first one is from my contact at Lippert and some of the extra wiring is from their…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 11

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Troubleshooting Flashing Yellow Lights of Lippert Ground Control

Product Page this Question was Asked From

Continue Researching