Is There a Front Hitch for a 2021 Jeep Wrangler Unlimited Hybrid

Question

Question:

I just purchased a 2021 Jeep Wrangler Sahara 4xE. The new hybrid version. Do you know if there is a front hitch that will fit these vehicles or if the standard Curt or other hitches for Jeep Wranglers will fit.

asked by: Ron

0

Expert Reply:

I do show the Curt Front Mount Trailer Hitch Receiver part # C31086 as a fit for all models of a 2021 Jeep Wrangler Unlimited so you'll be good to go with a Hybrid.

expert reply by: Conner L

0

Answer 1

I reached out both to Curt and Draw-Tite about the installation of their front mount hitches, parts #C31086 and #65079 respectively, on your 2018 Jeep Wrangler Rubicon and I pretty much got the same answer from both of them. The plastic pieces are…

view full answer...

Answer 2

There are a couple of pretty big differences between the Draw-Tite Trailer Hitch Receiver #DR64FR and the Curt Trailer Hitch Receiver #CU74FR that fit your 2020 Jeep Gladiator, and I'll go over them so you can decide which trailer hitch is the…

view full answer...

Answer 3

The Curt #13432 Class III hitch only fits JK models through 2018. for your 2021 Wrangler Unlimited, use the Curt #C13392. This fit is confirmed by Curt. I'm not certain where on our site you saw that the #13432 was a fit for the 2021, but when I…

view full answer...

Answer 4

For your 2022 Jeep Wrangler, the only difference between the etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish #e98856 and the Curt Hitch #C13392 is that the Curt hitch comes with a higher-quality gloss outer coating over the base…

view full answer...

Answer 5

Yes, the Curt T-Connector Vehicle Wiring Harness #C56407 will work on your 2021 Jeep Wrangler Unlimited Sahara 4XE. If you are needing a receiver I recommend the etrailer Trailer Hitch Receiver #e98856. This receiver is longer than other receivers…

view full answer...

Answer 6

I reached out to my tech contact at Curt and he said the Curt Front Mount Trailer Hitch Receiver #C31086 has been test fit on your specific Rubicon model and it is a confirmed fit. You will need to remove the steel skid shield permanently for this…

view full answer...

Answer 7

Hey Mark, so the correct Blue Ox base plate kit to use with the Blue Ox Ascent tow bar part #BX4375. is the part #BLU53FR. For lighting you can use #C96JR, and not have to worry about cutting into the taillight housing as this plugs inline with the…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...