Will the X-Factor Crossmember # MR33WR Fit on Existing CRE3000 Hardware?

Question

Question:

I want to buy three of these to put on existing cre3000 as well as leaf mounts. I have the HD shackle kit and was wondering if these will fit as is or if I need a different set of nuts and bolts for them to work.

asked by: Justin T

0

Expert Reply:

I went ahead and reached out to my contact at MORryde, and she confirmed that the X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension # MR33WR will come with new mounting hardware. The plates on the cross member do add thickness, so the bolts are longer to accommodate that thickness. The X-Factor Crossmember will work with your current CRE3000 hardware.

expert reply by: Bob C

0

Answer 1

Since you have a tandem axle trailer rated for 10,500lbs the 6-Leaf Double-Eye Spring for 5,300-lb Trailer Axles #e76SR are going to be the closest leaf springs we have to that weight capacity. These springs measure 24-7/8" from center of eye to…

view full answer...

Answer 2

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part #MR33WR.

view full answer...

Answer 3

The MORryde X-Factor Crossmember part #MR33WR is designed for standard suspension so that is the one you will need to use. If your leaf spring hanger brackets are wider than 3" then you will need to drill per the instructions which I have…

view full answer...

Answer 4

Yes you certainly can go from a 4 leaf to a 6 leaf spring on your 2020 Open Range 5th Wheel. It will add slightly to your ride height, but there should not be any other components that will be compromised or need to be swapped out. You will want to…

view full answer...

Answer 5

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part #MR33WR. This is the MORryde part number XF12-001.

view full answer...

Answer 6

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 7

Welcome back! You do not need to cut anything away! So long as your 5" of clearance was measured with your trailer loaded and resting on the suspension you will be good. The SumoSprings Trailer Helper Springs item #SS26MV include spacers that…

view full answer...

Answer 8

The leaf spring that best matches your description is the following from Universal Group: - 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR We measure our leaf springs when they are relaxed but Dexter will measure…

view full answer...

Answer 9

I spoke with MORryde and they said that the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR will work just fine with your frame hangers with gussets. You'll just need to use the circled items attached in the image below and…

view full answer...

Answer 10

I contacted MORryde and this does happen from time to time as the weight of the trailer can spread out the axles due to downward pressure on the springs/suspension. Odds are the 35" wheel base #MR27ZR will be the correct one for you, but they…

view full answer...

Answer 11

The MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR includes one adjustable crossmember. Your existing hardware will be too short due to the extra thickness of the crossmember, so you will need to add #MR58ZR if…

view full answer...

Answer 12

Yes, the 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles #e64SR will work as a replacement. The leaf springs on your 2012 Redwood 36FL have probably elongated as they wear out over time. Regardless, the 2/8" difference is negligible…

view full answer...

Will the X-Factor Crossmember # MR33WR Fit on Existing CRE3000 Hardware?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching