What Is the Pin Configuration on the RearViewSafety 2133 Quick Connect Kit

Question

Question:

Is the a description of the pinouts on RVS-2133? particularly the 7 pin truck to trailer cable

asked by: Tom M

1

Helpful Expert Reply:

I have attached a photo with the diagram of the pins on the # RVS-2133.

expert reply by: Erik B

1

wiring diagram
(click to enlarge)

Answer 1

The difference between those 2 Rear View Safety Backup Camera System with Trailer Tow Quick Connect Kits is the Kit #RVS-770613-213 comes with 1 camera while the Kit #RVS-770614-213 comes with 2 cameras. They both have the ability to connect up to 3…

view full answer...

Answer 2

The easiest way to tell if you need to upgrade your wiring is to disconnect your monitor and camera to check the connection points. You may be able to use your current wiring if you use an adapter like the Rear View Safety Splice Kit #RVS-SPK01. It…

view full answer...

Answer 3

The Custer LED Side Marker or Clearance Trailer Light #CPL120A doesn't require a rubber gasket. The wiring and LED's are sealed completely and there is no need for a gasket. If you are running the wiring into the wall be sure to use silicone…

view full answer...

Answer 4

We have not had anyone complain about the cameras in system #RVS-062710 becoming foggy and unusable as a result. This particular system comes with quad view monitor and 4 camera inputs. There is only one power wire that will need to be installed for…

view full answer...

Answer 5

For your setup, I recommend the Rear View Safety Backup Camera System with Side Cameras #RVS-062710 and Quick Connect Kit #RVS-2133. This will give you two additional cameras to allow you to see the blind spots from your trailer better for turns and…

view full answer...

Answer 6

The Dometic 300 Toilet, #DOM64FR has a total length of 19-3/4" with a minimum distance from wall to center of 8-1/2". The Dometic 320, #DOM87FR is overall length of 22" with a minimum distance from wall to center of 11". If you…

view full answer...

Answer 7

I have the perfect solution for you! To add a multiplexer to your Rear View Safety #RVS-619N-S system you can use the Rear View Safety Multiplexer Box #RVS-501N , which is the part that is normally included in the upgraded #RVS-770619N-S system.…

view full answer...

Answer 8

Thank you very much for your purchase from etrailer of the Rear View Safety Switcher Box #RVS-501N. I reached out to the manufacturer who said to me that the issue is that you're not receiving enough voltage, and that you will need to utilize…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

What Is the Pin Configuration on the RearViewSafety 2133 Quick Connect Kit

Product Page this Question was Asked From

Continue Researching