Adjustable Utility Light for Loading and Unloading a Horse Trailer at Night

Question

Question:

I am trying to find Halogen lights that are adjustable and bright for unloading my horses at night. Is this light bright enough I would order two to do the job? I didnt see an adjustable with two bulbs each.

asked by: Caren

0

Expert Reply:

The utility light # QH16CTS is a 55-watt halogen light (like a car head light) so it will be as bright as one low beam car light. I would go with 2 of these lights for your application. You will want to be able as see as much as possible when there are animals involved.

expert reply by: Michael H

0

Answer 1

I am not sure which flood light that you are referring to but if you know the type and wattage rating of the bulb then you can get a good idea of the lumen output. The Optronics Halogen Utility Light part #QH16CTS for example contains a 35 watt…

view full answer...

Answer 2

To change the bulb on the Optronics Halogen Docking Light, part #DL-16CC, you just remove the 2 screws that are on the front of the light, one on each side of the lens. You then need to pull the assembly out of the housing and on the back there is a…

view full answer...

Answer 3

The Opti-Brite LED Work Light #TLL60FB is a 2-wire light with black being power and white being ground. It will wire in to your trailer's existing wiring. As long as the current lights run on 12, 24, or 36 volt DC this light is compatible.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 11

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 12

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...