Will Reese 14K 5th Wheel Hitch Work With Curt Custom Fifth Wheel Installation Kit

Question

Question:

i have a reese 14k classic above the bed hitch, will this work with curt brand rail and mounting kit #16411-204 for my 2019 silverado 2500? also is all hardware necessary for mounting the rails and brackets included?

asked by: Damon S

0

Expert Reply:

Yes, you can use the Reese 14K 5th Wheel Hitch with a Curt Custom Fifth Wheel Installation Kit like part # C16411-204.

expert reply by: Conner L

0

Answer 1

Yes, the Curt Fifth Wheel Installation Hardware part #C16411-204 that you referenced has been confirmed to fit a Pro Series 15k Fifth Wheel Hitch like what you have. The rails of this hardware kit are confirmed to fit Curt, Draw-Tite, Hidden Hitch,…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 6

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 7

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 8

The head alone for the B&W Companion hitch #BWRVK3500 weighs about 70 pounds. Everything else weighs about 130 pounds. So the total weight of the hitch is approximately 200 pounds.

view full answer...

Answer 9

You can replace the Lippert Rhino pin box on your Brinkley 5th wheel. The right one though is going to depend on the pin weight of your trailer. Here are the options that will work to replace the Lippert Rhino: - Pin Weight of 1,500 lbs - 3,500 lbs:…

view full answer...

Answer 10

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 11

Hey Mark, since we know your Brinkley Z3100 has the Rhino style pin box, the correct Gen-Y fifth wheel to gooseneck adapter is the part #GY98GR which comes with the auto latch you mentioned wanting as well!

view full answer...

Answer 12

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Will Reese 14K 5th Wheel Hitch Work With Curt Custom Fifth Wheel Installation Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching