Drop Leg For etrailer Round, A-Frame Jack TJA-5000S-B

Question

Question:

What leg would be appropriate for the 5000 lb etrailer a-frame jack I ordered?

asked by: Garrett H

0

Expert Reply:

We do have a drop leg that is compatible with the etrailer Round, A-Frame Jack # TJA-5000S-B.

The drop leg needs to fit the jack tube's 1-3/4" inside diameter, and for that you will need the Drop Leg for etrailer and Ram Jacks - 13-1/4" Tall - 5-1/4" Diameter Footplate - Zinc # JF-1005H-Z.

I have added some links below to video reviews for you to check out as well.

expert reply by: Kyle S

0

Answer 1

The Bottom Support Plate for 2-1/4" OD A-Frame Jacks - 5,000 lbs #JSP-100 you mentioned is 1/8" thick, has a hole diameter of 2.29", 8-3/4" long at the back, 5-1/2" long at the front, the diagonal sides are 3-7/8", and…

view full answer...

Answer 2

In my opinion you are going in the right direction with a frame mounted receiver. The only advantage to a weld on application is that, if welded properly, the attachment point, weld, will be stronger than the hitch or trailer frame steel and one of…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...