Will the Replacement Mounting Hardware for Thule Weekender Fit Factory Bars on Subaru Outback 2019

Question

Question:

Hi, Would the 1032802 Quick Mount Hardware Kit suffice for the 2019 Outback? Wondering before purchasing Weekender.

asked by: Francis S

0

Expert Reply:

The Replacement Mounting Hardware for Thule Weekender Cargo Box # 1032802 will work on a variety of crossbar shapes, including the factory bars on your 2019 Subaru Outback. So, yes; this kit will work to allow you to replace the hardware on a Weekender cargo box and use it on your Outback.

expert reply by: Erik B

0

Answer 1

You can use the QM3 mounting hardware #TH04997 for the Weekender rooftop cargo box. This will use the carriage bolts as you stated and will fit 4 inch on center holes. I've attached some photos and a video to assist.

view full answer...

Answer 2

I went to the warehouse and took a look at the Replacement Mounting Hardware for Thule Weekender Cargo Box #1032802, and it does in fact have 8 bolts.

view full answer...

Answer 3

I spoke with my contact at Thule and she informed me that this Thule QM3 Quick On-Off Mounting Hardware Kit #TH04997 would be the correct hardware kit for your 1997 Thule Weekender and should allow it to attach to the cross bars of your 2010 Honda…

view full answer...

Answer 4

If your Evolution cargo box is the type that has a slot the feet slide in then you can use the EasySnap u-bolt replacement, #43216. There isn't another option for that fit and that entire assembly has been discontinued. If you have an older cargo…

view full answer...

Answer 5

Yes, you can drill new holes in your Thule Frontier Cargo Box in order to clear the rear hatch on your 2018 Subaru Outback Wagon. I also recommend using part #LT37467 to cover up the old holes so water doesn't get in. The only thing you need to…

view full answer...

Answer 6

Yes, the Replacement EasySnap Mounting Kit for Thule Cargo Boxes, part #43216 that you referenced is the correct replacement hardware for your Thule Evolution 1600 cargo box if it came with the EasySnap base. If not, then you will use the kit…

view full answer...

Answer 7

We have the correct replacement mounting hardware for your Thule Evolution Cargo Box, but the QM3 #TH04997 is not the correct hardware kit unless your holes are 4 inches on center at the mounting locations. To replace the mounting hardware for your…

view full answer...

Answer 8

Yes, you can drill new holes in your Thule cargo box in order to mount this on your 2016 Subaru Crosstrek. When you drill the holes you need to make sure you maintain the correct spacing for your existing mounting hardware. After drilling new holes,…

view full answer...

Answer 9

I spoke with my contact at Thule and he informed me that you should have no problem installing your Thule Evolution 1600 cargo box on the factory cross bars of your 2012 Honda Pilot Touring. You should consult your owners manual to determine the…

view full answer...

Answer 10

I spoke with my contact at Thule to see if your cargo box was possibly made by them. My contact confirmed that they did make several cargo boxes for Subaru and one of them did look like the Evolution 1600. My contact at Thule confirmed that the Quick…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...