Parts Needed to Install Thule Square Crossbar on 2019 Honda CR-V

Question

Question:

Im placing a Thule fit kit and podium foot on my 2019 Honda CRV so I can use my existing 53inch crossbars that I had on my Lexus. I cant find good directions or videos for doing this. Any suggestions?

asked by: Mary B

0

Expert Reply:

The square bar Thule roof rack components you need for a 2019 Honda CR-V are # TH712400, # TH710501, and # TH145046. You should note that Thule phased out the Podium feet as well as changed their square bars to now have a channel on the bottom of the bars instead so if you have the older bars then we don't have a way to fit to your new vehicle.

expert reply by: Jameson C

0

Answer 1

The Thule Traverse 480 has been discontinued and is only compatible with square load bars which are also discontinued. The Thule Rapid Traverse Foot Pack #TH480R are compatible with the Aero Style bars like the AeroBlade or WingBar Evo, the ProBar…

view full answer...

Answer 2

The Fit Kit for Thule Evo Clamp Roof Rack Feet part #TH145086 which is correct for your 2011 Volkswagen CC will not work with the older Thule Traverse Foot Packs. The Thule Traverse Foot Packs and Thule Fit Kits for Traverse Foot Packs are all being…

view full answer...

Answer 3

Yes you can use the Thule Fit Kit #TH145046 with your Thule Rapid Traverse Foot Pack on your 2017 Honda CR-V. This fit kit is compatible with both styles of feet. The Evo Clamp Feet for Thule Crossbars #TH710501 is replacing the Rapid Traverse…

view full answer...

Answer 4

To get the older style square cross bars to work on your 2020 Honda CRV, per Thule you are going to need the 480 foot pack with the 1855 fit kit. The 480R is not compatible. Both of these are discontinued items which Thule does not carry any longer.…

view full answer...

Answer 5

In order to transfer the Thule AeroBlade Crossbars you have onto a 2019 Honda CR-V you will need the Evo Clamp Feet part #TH710501 and Fit Kit for Thule Evo Clamp Roof Rack Feet part #TH145046. I know this is not what you wanted to hear but the…

view full answer...

Answer 6

That is correct, naked roof mounts attach to the (vehicles) VEHICLE'S door frame with custom fit kits. If you get the add on roof rack you will need a different custom fit kit to mount to the Honda's rails instead. I recommend an Aero style…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 9

Aside from a slight change in the appearance of the crossbar (the WingBar Evo has some boxed edges as opposed to the completely smooth front of the AeroBlade) the biggest differences are the rubber strip on top of the crossbar and the weight…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

Thanks for reaching out, Joe! I recommend using the Rhino-Rack Aero Bar Roof Rack for Camper Shells #Y02-480B which comes with 63" long tracks as well as 54" long crossbars which should give you a little bit of overhang on your canopy. Per…

view full answer...