Availability of Tandem Trailer Fender that is Near 11 inches Wide

Question

Question:

Hello, I am looking for this exact fender in an 11inch width instead of 9inch to cover up the wheels completely on a flatbed trailer. Do you have these in an 11inch width? Thanks,

asked by: Chris K

0

Expert Reply:

We have a couple tandem trailer fenders that are 10-3/4 inches wide like with the part # HP84VR and the # HP74VR which are both 72 inches in length but at the 68 inch length of the # HP64VR

expert reply by: Jameson C

0

Answer 1

For your Tandem 8K axles with 2 inch slipper springs, I recommend the Tandem-Axle Trailer Hanger Kit for 2" Slipper Springs - 12" Long Equalizers #APT6SE. The hangers are to be welded to your trailer frame and the holes on the top of the…

view full answer...

Answer 2

The Backing Plate #HP72FR can be cut to match the Tandem Axle Teardrop Trailer Fenders #HP64VR. The fender is made of 16 gauge steel and the backing plate is 18 gauge steel if you plan to weld them together.

view full answer...

Answer 3

The best recommendation I can give you would be to replace your current jack with a Bulldog Jack like our part #BD182804 and then get a Bulldog Powered-Drive Kit #BD1824200100. The powered drive kit is only confirmed to fit Bulldog jacks so you would…

view full answer...

Answer 4

Yes, this could happen with a bent spindle. I recommend replacing the entire axle and not just a spindle. Just replacing the spindle can be problematic because the new spindle will need to be welded EXACTLY straight. The spindle needs to be centered…

view full answer...

Answer 5

The attachment bolts for a 5-bolt brake assembly like the part #AKEBRK-6R should be torqued to 30-50 foot/lbs. If you don't have a torque wrench handy, if you tighten the bolts until the lock washers flatten out, you'll be pretty darn close…

view full answer...

Answer 6

We do have several tandem axle trailer fender setups that could work for your horse trailer but I would need the length of your current fenders as we don't have a way to look that up for your trailer. For example the part #HP64VR is 68 inches…

view full answer...

Answer 7

The C-Channel for Enclosed Trailer #362213-955 has an opening of 1.027". I have included an image below with all the dimensions for this item.

view full answer...

Answer 8

The smaller section of the Z-Rail for Enclosed Trailer #362417-955 is approximately 3/4" tall, while the larger section is approximately 1-1/4" tall.

view full answer...

Answer 9

A galvanized steel fender like #CE17701G has a corrosion-resistant zinc coating applied to it, while a raw steel fender like #CE17720 does not. Both types can be painted, but it will be easier to paint the non-galvanized part. In either case the…

view full answer...

Answer 10

The Transcom #TCM 21344 TB cross references to the 10-10 seal we offer, part #RG06-090. The seal has a 2.125 inch ID and a 3.376 OD. It's compatible with a 25580 inner bearing.

view full answer...

Answer 11

On this page (typically below the product links) there is a helpful link section that will have the install instructions fo the Hopkins Breakaway kit part #20400 that you referenced. I also attached an install video that shows the kit installed as…

view full answer...

Answer 12

The Backing Plate #HP72FR can be cut to match the Tandem Axle Teardrop Trailer Fenders #HP64VR but we do not have any custom backing plates that fit the #HP64VR.

view full answer...

Availability of Tandem Trailer Fender that is Near 11 inches Wide

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching