2002 E350 Super Duty Dually Cutaway RV

Question

Question:

Looking for a rear sway bar for my 2002 E350 Super Duty V10 6.8L 23ft Dually Cutaway RV. This RV has no rear swaybar. Refer to pictures. Other notes on the RV: Ford 158 Super Duty Cutaway, E35Y series SD Commercial Cutaway.

asked by: Doug P

0

Expert Reply:

For a 2002 Ford E350 Class-C RV, the correct rear stabilizer kit is Roadmaster # RM-1139-117 which will definitely help with cross winds and passing vehicles. If you decide you would like more stability you could additionally add the Roadmaster # RM-1139-115 front stabilizer.

expert reply by: Les D

0

Answer 1

Roadmaster offers an anti-sway bar that is confirmed to fit your 2004 Ford E350 cutaway box van. You would want the Roadmaster Sway Bar part #RM-1139-117. If you wanted a front sway bar you would want the Roadmaster Front Anti-Sway Bar #RM-1139-115.…

view full answer...

Answer 2

For your vehicle the I recommend the Roadmaster Front Anti-Sway Bar Item #RM-1139-115 and the Roadmaster Rear Anti-Sway Bar Item #1139-178. I verified your VIN number with Roadmaster to ensure these were a confirmed fit.

view full answer...

Answer 3

Anti-sway bar #RM-1139-115 does replace the factory sway bar on the 1998 Ford E-450 Class C motor homes.

view full answer...

Answer 4

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 5

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 6

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 12

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

2002 E350 Super Duty Dually Cutaway RV

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching