Can MaxxAir MaxxFan Mini Roof Vent be Used With Wall Switch

Question

Question:

I am planning to replace the bathroom vent fan unit in my 2005 Jayco Eagle. The current fan is operated by a wall switch. Can this replacement Maxxair unit be operated by a wall switch or only with the push buttons on the unit itself? Thanks

asked by: Kyle S

0

Expert Reply:

We have trailer roof vents that have an included wall switch you can use, but it is not recommended to use one with the MaxxAir MaxxFan Mini Roof Vent with 12V Fan # MA00-04301M because this vent is meant to have 12 volt power constantly, and a switch interrupts the voltage, which could damage the circuit board.

If you'd like, what you can use instead is an option from Ventline which includes the wall switch for simple use:

- Ventline Ventadome Roof Vent with 12V Fan and Wall Switch # V2119-1-533

I have added a link below to a video review for you to check out as well if you'd like to take a look.

expert reply by: Kyle S

0

Answer 1

The difference between the two Fastway weight distribution systems you mentioned is the bar style of either. The Fastway part #FA92-00-0600 uses trunnion bars which many prefer as you get more ground clearance with them and the part #FA94-00-0600 is…

view full answer...

Answer 2

If you are just looking for a new converter, the Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers part #PD4635V will be a direct upgrade for the Magnetek Converter Series 6300 Model 6332 that you have now.

view full answer...

Answer 3

The MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - White #MA00-04301M is made in China. It has a 2 year limited warranty on the vent assembly and a limited lifetime warranty on the dome However I do recommend the Fan-Tastic Vent…

view full answer...

Answer 4

The MaxxAir MaxxFan Mini Roof Vent w/ 12V Fan - Manual Lift - 4 Speed #MA00-04301M that you referenced would not let any light in since the lid is totally solid so for a semi-opaque lid you'd want the smoked version part #MA00-04401M.

view full answer...

Answer 5

The MaxxAir #MA00-04301M fan that you referenced is not reversible. It exhausts air only. However, the Fan-Tastic Roof Vent #FV802250 is reversible and has three speed levels and a tinted vent cover. If you don't already have one, most users…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Donald, the best Blue Ox weight distribution would be the pat #BXW0550 as it has a perfect tongue weight range for your 450 lb tongue weight trailer.

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

Most of the 2-5/16 inch hitch balls will use either a 1-inch diameter shank or 1-1/4 inch diameter shank. The nut size on a hitch ball with a 1-1/4 inch shank, like the Tow Ready 2-5/16 Inch Hitch Ball, part #19286, will use a 1-7/8 inch socket. A…

view full answer...

Can MaxxAir MaxxFan Mini Roof Vent be Used With Wall Switch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching