Replacement Step Switch On A 2014 Georgetown Forest River 329

Question

Question:

I need to replace the switch for my retractably step on my Georgetown Forest River 329. The switch thats currently there is a Carling Technologies 1305R 12 volt lamp. Thanks for your help.

asked by: Dan L

0

Expert Reply:

To replace the switch for your steps in your 2014 Georgetown Forest River 329, I recommend the Universal-Design Rocker Switch Item # PK34310. This is a simple on/off 20 amp, 12v switch with a light.

expert reply by: Shane H

0

Answer 1

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

Yes, the MORryde StepAbove RV Steps with Strut Assist like #MR85RR can use the removable mounting plate. It isn't compatible with the struts but you already plan to remove them so that won't be an issue. Assuming you have a 26-28" wide…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

I have a solution that may work for you, but we do not currently have any 3" diameter submersible reverse lights. Have a look at the Optronics Backup Light #BU45CB which is a 4-1/4" diameter light that can be mounted to your trailer using…

view full answer...

Answer 6

Since the inverter would output 12 volts it would be the same running the Therma heat RV tank pad heater part #277-000164 to that as it would be a 12 volt battery.

view full answer...

Answer 7

For starters, I have attached a photo of how the Universal-Design Rocker Switch part #PK34360 should be wired. However, I believe the issue you are having is in regards to the size of wire used. The correct size or (gauge) will vary depending on…

view full answer...

Answer 8

You can daisy chain multiple heating pads like the part #277-000163 together and run them to a switch like the part #PK34310 if you'd like. I attached a diagram that shows how they would all go together as well.

view full answer...

Answer 9

Though I do not know exactly how much your converter sends to the trailer batteries while hooked up to shore power, I would be willing to bet it exceeds the 4.8 amps of the ThermaHeat RV Holding Tank Heater Pad part #277-000164. Please keep in mind…

view full answer...

Answer 10

The gauge wire used on the 18-1/4" x 12" Holding Tank Heater Pad #277-000164 that you referenced is 14 gauge.

view full answer...

Answer 11

A device like the ThermaHeat RV Holding Tank Heater Pad #277-000164 will function for as long as your battery has power, but this time period can vary quite a bit depending on the battery capacity and condition. Since this item also has a thermostat…

view full answer...

Answer 12

The ThermaHeat RV Holding Tank Heater Pad, Item #277-000164, will need to be connected to a 12 volt power source. You should be good to go and you just need to follow the installation instructions for safety and security. I have attached a short…

view full answer...

Replacement Step Switch On A 2014 Georgetown Forest River 329

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching