How To Determine Which Grease Cap Fits 6000lb Axle

Question

Question:

Grease Cap for Nev-R-Lube Hubs - 3.355 Outer Diameter - Single Lip 75DC Is this part for a 6k axle? Thank you

asked by: Jennifer

0

Expert Reply:

The Grease Cap for Nev-R-Lube Hubs # 75DC you were looking at may fit the hub on your 6000lb axle, but the only way to confirm this is to measure the hub bore of your hubs as shown in the included diagram.

The # 75DC is for hub bores that measure 3.355" so if this matches your hub this would be a great replacement option. If you have a different hub bore diameter just let me know.

I included a link to all of our grease caps, and a video of the # 75DC for you to take a look at.

expert reply by: Samuel C

0

Where To Measure Hub To Determine Hub Bore Diameter
(click to enlarge)

Answer 1

I reached out to my contact at Dexter Axle and he said that the little bit of grease you are seeing is normal for the 50MM Nev-R-Lube Bearing #31-71-3. The race that you mentioned should be able to rotate but it should not be moving in and out. If…

view full answer...

Answer 2

From the pictures you sent in it looks like the inner diameter of your Nev-R-Lube bearing is about 2" which means you'd need the 50MM Nev-R-Lube Bearing for 8,000-lb Dexter Axles #31-71-3. Aside from that you're basically just going to…

view full answer...

Answer 3

The great things about the 50MM Nev-R-Lube Bearing for 8,000-lb Dexter Axles part #31-71-3 is they do not require grease. They are a bearing, race and seal built into one pre-greased from the factory. You can use a very small amount of anti-seize…

view full answer...

Answer 4

Dexter Nev-R-Lube Bearings such as the 50MM #31-71-3 referenced in your question do not have a specific maintenance or replacement schedule. These are pre-lubricated at the factory, which will make it resistant to contamination, and sealed for life…

view full answer...

Answer 5

The valve stem #AM20906 used to only include one grommet that fit the 0.625 hole diameter but now includes both. If it's tight and torqued down properly (Between 25 to 55 inch-pounds technically), the nut will not loosen during travel. Although,…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...