Replacement Landing Gear 2006 Keystone Sprinter

Question

Question:

looking to replace the landing gear legs. trailer is 2006 keystone sprinter copper canyon. there is no sky or other markings on the legs. the distance from the bottom of the upper bracket the top of the lower bracket is 11 inches. the length of the outer tube is 29-30 inches. I would like to replace both legs and the crossbar.

asked by: William B

0

Expert Reply:

For your 29-30 inches measurement, please look at the Replacement Lead Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2", # LG-179013 and its counter part the Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2", # LG-179014.

I suggest the Cross Shaft Extension Tube for Bulldog Tandem Landing Gear - 72-3/4" Long - Fixed # BDCS730300.

You state that the bracket is at 11", if so you may need to remove adjust location and reweld.

Please note the attached video links for product review and installation.

expert reply by: Michael R

0

Answer 1

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

The correct replacement for your 1-065-041012-01 motor is part #LC141893 from Lippert. Your original motor had a 7140 rpm speed. The Stromberg-Carlson #LG-196308 you specified has a 5430 rpm output, so it wouldn't be a good choice. You'll…

view full answer...

Answer 6

From what I could find it looks like your ADTH 1RV-200 motor has a weight capacity of 6,500 lbs. You can use a motor that is rated for a higher capacity, like our replacement motor #LC142178 for Ram landing gear which is rated at 8,000 lbs. Just keep…

view full answer...

Answer 7

Correct, the Advent Air RV Air Conditioner System #ACM150CH is a brand new install, so it won't use any of the original stuff. There is a built in thermostat, but there is not a remote so if you needed to change the temperature you'd need to…

view full answer...

Answer 8

I'm assuming you're wanting to add a brand new unit to your Keystone, in which you're going to want the Advent Air RV Air Conditioner System - Single Zone #ADV64FR. This is exactly what you'll be needing, including a air distribution…

view full answer...

Answer 9

The best connector type to use with the 40' 18-Gauge 2-Wire Bonded Wire #SWC77FR are the Deka Heat Shrink Butt Connectors #DW05743-10. You'll insert the ends of the wires into the butt connector, crimp it down, and then use a heat gun or a…

view full answer...

Answer 10

The Replacement Gearbox for Venture Aluminum Electric 5th Wheel RV Landing Gear #LC276602 is the one you will need for your 2005 Keystone Sprinter 252RLS 5th wheel. It is a direct replacement for your damaged Venture gear box.

view full answer...

Replacement Landing Gear 2006 Keystone Sprinter

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching