Correct Replacement Cover For Extang Tuff-Tonneau Cover # EX14650 On A 2019 Chevrolet Silverado

Question

Question:

I have a 2009 Chevy Silverado 1500 with a 6.5 foot bed. Im not sure what size of replacement cover to order. I have the roll-up, non-snap cover Tuff-Tonneau? with what I think is the J-hook design. Can you help? Photo1 shows the edge banding of my top, and photo2 shows my tailgate rail. Thanks

asked by: Paul M

0

Expert Reply:

It seems like you have the Extang Tuff-Tonneau # EX14650. This is the correct replacement cover for your 2019 Chevrolet Silverado 6.5ft bed # EX13650.

expert reply by: Adam E

0

Answer 1

The replacement cover for your Extang Tuff Tonno Soft Tonneau Cover - Snapless J-Strip - Roll Up - Vinyl #EX14650 on your 2010 GMC Sierra 1500 is #EX13650. I contacted the manufacturer to confirm this fit for you.

view full answer...

Answer 2

When it comes to a replacement tarp for the Extang Tuff Tonno Soft Tonneau Cover, #EX14660, on your 2007 Chevrolet Colorado, you will need part #EX13660.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 9

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

Since the Truxedo Lo Pro you'd have installed on your 2013 Chevy Silverado 3500HD long bed would be the part #TX571601 the correct replacement tarp would be the part #TX5716-CVR.

view full answer...