Availability of Jack Mounts for Trailer and Jack Side with Pin

Question

Question:

Im looking for a swivel jack mount, but Im not going to use it for a jack I just need sort of a base plate that swivels and locks at 90 degree intervals. I see a lot of the plate that that goes on the trailer, but not the corresponding part that would go on the jack. Do you sell both halves so I can make my custom swivel base plate?

asked by: Chris

0

Expert Reply:

You could use the 2-1/2 inch male mount part # BD005024 with the 2-1/2 inch female mount part # BD015279 and then for a pin part # BD500231.

expert reply by: Jameson C

0

Answer 1

Yes, I went out to the warehouse and verified that the Replacement Pipe #TJP-OP58 and the Bulldog 2-1/2" Long, Weld-On Jack Pipe Mount #BD005024 are compatible with each other. Review videos for both products have been linked for you to…

view full answer...

Answer 2

I went out into our warehouse and pulled a Bulldog Round, Pipe-Mount Swivel Jack, part #BD178203, that has the same 2 inch inner diameter and 2.5 inch outer diameter pipe mount swivel jack as yours. I then test fit a Bulldog 2-1/2 inch Long, Weld-On…

view full answer...

Answer 3

Pipe mount #BD005024 is the correct match for Bulldog jack #BD190758. The mating end on the jack fits inside of this mount which gets welded to the trailer frame. I have linked a video of the mount for you.

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 8

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 9

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 10

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 11

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 12

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Availability of Jack Mounts for Trailer and Jack Side with Pin

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching