Suspension Enhancement that Fits 1998 Chevy K2500 with In-Bed Gooseneck Hitch

Question

Question:

I have a 1998 Chevy K2500 crew cab short bed with a BandW Turnover Ball Installed. Is there a airbag kit I can install without interfering with the turnover ball. I was looking at the 2025 but I don’t think it’s going to work. Thank you.

asked by: Ryan B

0

Expert Reply:

For your 1998 Chevy K2500 we have suspension enhancement that fit with an in-bed hitch like the Timbren part # TGMRCK25 but we do not have any air bag kits that fit your truck configuration.

expert reply by: Jameson C

0

Answer 1

The Timbren kit part #TGMRCK25 that you referenced comes with two spacers which push the rubber spring further away from the bracket it is attached to which allows for it to engage at the proper time.

view full answer...

Answer 2

I checked with Timbren and the bolts that come with the Timbren part #TGMFK25S that you referenced are M10x1.5X30.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

I would be happy to! To flat tow your 2024 GMC Canyon Denali you will need the following parts: Tow Bar and Safety Chains - Roadmaster Nighthawk All-Terrain Tow Bar w/ LED Lights item #RM-676 Base Plate Kit - Roadmaster Direct-Connect Base Plate…

view full answer...

Answer 5

Personally I wouldn't go with Timbren's for your needs. They're essentially rubber bump stops that prevent your suspension from flexing when weights placed on the rear of your Canyon. The major issue with them is…

view full answer...

Answer 6

Yes, I checked with Air Lift and the Air Lift LoadLifter 5000 Air Helper Springs part #AL57216 are listed as a fit for a 1994 Chevrolet C/K Series 1500 (All Cab/Bed Types).

view full answer...

Answer 7

I have a solution for you. We do not carry hardware kits for the Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K #DM37ZR. However the instructions will give you the dimensions you will need and you can…

view full answer...

Answer 8

The Timbren Rear Suspension Enhancement System #TGMRCK25 are the correct fitment for your 1996 GMC K2500 Pickup. These provide up to 6,000lbs of support to your suspension components. They may help to level your vehicle but as they are designed to…

view full answer...

Answer 9

For air helper springs to use on your 1994 Chevrolet C/K Series Pickup 3500, I recommend going with the Firestone Ride-Rite Air Helper Springs, part #F2025. These are double convoluted springs which means they will last a little longer and wear…

view full answer...

Answer 10

We do have a really great selection of roof rack systems that are confirmed to fit the naked roof on your 2019 Kia Sorento. I specifically recommend the Yakima JetStream setup that consists of part #Y00425 for the two 50" JetStream Crossbars in…

view full answer...

Answer 11

From an install point of view the part #TGMRCK25 will still install just fine since the spring attaches to the frame of the truck and not the axle. If the axle is larger or smaller in diameter it would change when the spring engages. If it was bigger…

view full answer...

Suspension Enhancement that Fits 1998 Chevy K2500 with In-Bed Gooseneck Hitch

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching