Recommended Hand Winch with Strap for 1,500 Lb. Boat

Question

Question:

Please provide models numbers on a boat trailer winches replacement * base of winch cannot exceed 5 wide * nylon strap or polyester * boat weight totals 1500 lbs fully loaded

asked by: Ron G

0

Expert Reply:

The Buyers Products Trailer Hand Winch part # 337HW800S seems to fit the bill for your boat trailer. The mounting base is 3-1/2" wide, it comes with an included nylon strap, and it has a 800 lbs weight capacity which using the standard 2:1 ratio will work great for boats up to 1,600 lbs.

expert reply by: Conner L

0

Answer 1

Yes, the Buyers Products Trailer Hand Winch - 800 lbs #337HW800S has a ratchet and free spool function. The linked video will display how it operates. I do however recommend looking at the Dutton-Lainson Hand Winch - TUFFPLATE Finish - Single Speed…

view full answer...

Answer 2

The mounting holes on the bottom of the CE Smith Galvanized Winch Stand #CE31013G measure 7/16-inch. Please refer to the linked photo. This 30-inch tall winch stand is made of 12-gauge steel and is intended for 2-inch trailer tongues. It is…

view full answer...

Answer 3

To mount the CE Smith Winch Stand #CE31013G on a trailer requires you to slip the lower portion with the holes drilled through it over the pole tongue of your trailer. The various holes are there to allow you to match the correct height and angle…

view full answer...

Answer 4

Sounds like you are looking for a winch mount like #CE31013G. The stand is made of 12 gauge steel and measures 30-inches tall. It has 14 mounting holes and fits a 2 inch wide trailer frame.

view full answer...

Answer 5

The height of the frame does not matter, just the width. So with a 2 inch wide frame you can install CE Smith Winch Stand #CE31013G.

view full answer...

Answer 6

The MaxxTow MaxxHaul Hand Winch part #MT50156 will work just fine with the CE Smith Winch Stand part #CE31013G. There will be no additional winch mounting plate needed, you'd just bolt the winch base directly to the stand. There are pre-drilled…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Recommended Hand Winch with Strap for 1,500 Lb. Boat

Product Page this Question was Asked From

Continue Researching