Replacement T-Bolt and Locking Arms for Ram M25 Factory Hitch

Question

Question:

I have a Ram M25 5th wheel hitch. I need replacement attach anchors T Bolt and locking arms. 4 of each, will the curtis Q25 parts work on my M25?

asked by: Larry P

0

Expert Reply:

The parts for the Curt Q25 Fifth Wheel Hitch will fit the Ram M25 hitch. The parts that you need are the following:

-Replacement Handles for Curt 5th Wheel Hitches for Ram OE Towing Prep Package # C78UR

-Replacement Rear Anchors for Curt 5th Wheel Hitches for Ram OE Towing Prep Package # C48UR

expert reply by: Jacob H

0

Answer 1

Curt is the manufacturer of the Mopar branded 5th wheel trailer hitches. For example, the Mopar 5th Wheel Trailer Hitch part 82214742 is the same as the Curt Q20 5th Wheel Trailer Hitch part #C16530-16021 and the Mopar 5th Wheel Trailer Hitch part…

view full answer...

Answer 2

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 12

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Replacement T-Bolt and Locking Arms for Ram M25 Factory Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching