High Volume Roof Fan and Vent Cover

Question

Question:

looking at maxxair maxxfan mini roof vent MA00-04401M need to move a lot of air, is this the right choice, also need a cover that will go above the vent.

asked by: Denny A

0

Expert Reply:

Since you want to move a lot of air and you want a cover for your fan I recommend the MaxxFan # MA00-06401K that combines both the fan and cover in one product. The cover design is probably the best for keeping rain out. I think this full size fan will probably move more air than the low-profile "mini" that you mentioned.

expert reply by: Les D

0

Answer 1

I reached out to my tech contact at MaxxFan and confirmed the MaxxFan Deluxe Roof Vent w/ 12V Fan - Manual Lift - 4 Speed - Smoke #MA00-06401K can be left open while traveling at highway speeds. You won't need to have the cover like the more…

view full answer...

Answer 2

I spoke with my contact at MaxxAir regarding the MaxxFan Deluxe Roof Vent #MA00-06401K. He said that while it technically can be done, they do not recommend wiring any of their fans to a separate switch. The reason for this is that their fans are…

view full answer...

Answer 3

The MaxxFan Deluxe Roof Vent part #MA00-06401K will work great in place of a Fantastic Vent. The hole size will be the same so no additional trimming should be needed and if the old unit already has power ran you can simply splice into these wires.…

view full answer...

Answer 4

That is a great question, the answer is dependent on the power draw of this fan relative to available energy from vehicles power source. If you are operating off only the crank/start battery that will be a relatively short period of time before there…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the correct roof vent, measure where the vent opens. The standard trailer roof vent opening is roughly 14-1/4" x 14-1/4" and have roof vents that measure 14" x 14". To pick the correct cover, you will also…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

The MaxxFan Deluxe Roof Vent w/ 12V Fan and Thermostat item #MA00-06200K uses up to 5-Amps to operate when running and up to 9-Amps for startup. So probably between 90 - 100 hours if it was the only thing running and you left it on.

view full answer...

Answer 12

Thanks for the pictures of your roof vent lid Marty! Based on that the correct replacement is the Ventline part #BVD0449-A01 that you referenced if you wanted white or the part #BVD0449-A03 for the same smoke color you have now.

view full answer...