Availability of Replacement Brake Assemblies for 8k Al Ko Axle from Dexter

Question

Question:

Hi, I have a AlKo 8K brake and I would like to replace it with a Dexter 8K brake. Would I have any problems with replacing? Do they have the same axle hole size and bolt pattern?

asked by: Brian S

0

Expert Reply:

For AL KO 8k axles we have the replacement brake assembly set part # K23-532-533-00 which comes with a set for both sides of the axle. This kit is made for the Al Ko axles by Dexter and has the unique bolt pattern and width that the Al Ko setups have.

expert reply by: Jameson C

0

Answer 1

The Dexter Electric Trailer Brake Assembly #K23-532-00 has a square mounting pattern with the bolt holes centers being 3-3/4" on center. This particular assembly is for the drivers side of the 8,000-lb AL-KO / Hayes axle. We also have the…

view full answer...

Answer 2

The four bolt brake mounting flange for 8,000 lb trailer axles is going to be more or less an industry standard. This industry standard is 3-5/8" across left to right on center and 3-7/16" top to bottom on center. This could very…

view full answer...

Answer 3

The Dexter Electric Trailer Brake Kit - Self-Adjusting - 12" - Left Hand and Right Hand - 8K #K23-532-533-00 is the correct replacement if your Hayes axle has brakes measuring 12" in diameter and 3-3/8" wide. This kit…

view full answer...

Answer 4

Knowing your axle's weight capacity - in your case 8,000 lbs - is the first step towards finding the correct replacement brakes. The brakes you referenced, which are sold together as the Electric Trailer Brake Kit #AKEBRK-8, also have a 4 bolt…

view full answer...

Answer 5

The pilot hole on the 12-1/4" Electric Trailer Brake Kit w/ Dust Shields #AKEBRK-8 is about 4" so it will work for your application. You will want to make sure the bolt holes line up with what you have though so I'm attaching a photo…

view full answer...

Answer 6

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 7

Is there any tag or label on your axle that would help identify it? You could possibly have a AL-KO/Hayes axle that used a 4 bolt pattern that measured as follows: • The top two holes are 3-1/8 inches apart • The bottom two holes are 2-1/2 inches…

view full answer...

Answer 8

The Dexter Electric Trailer Brake Kit #K23-532-533-00 is for 8,000 lb axles and has a 4-bolt pattern that is 3-7/16" across and 3-5/8" vertically. They would mount to a 4-bolt brake mounting flange such as Trailer Brake Mounting Flange…

view full answer...

Answer 9

When our installers replace a trailer hub, there isn't a set torque spec used when tightening the spindle nut. The hub is placed on the spindle, making sure the inner and outer bearings are correctly seated. The spindle nut is then run down until…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Availability of Replacement Brake Assemblies for 8k Al Ko Axle from Dexter

Product Page this Question was Asked From

Continue Researching