Replacement Pipe Mount to Use with Pro Series Jack # PS1401080303

Question

Question:

Im interested in purchasing this stabilizer jack: PS1401080303. I want to also purchase additional brackets to weld to my trailer so i can move the jack to different spots. What are the dimensions of the male bracket that welds to the trailer that comes with the jack length, diameter, pin hole size, etc.? And do you offer this bracket separately?

asked by: David

0

Expert Reply:

For additional pipe mounts to use with the Pro Series trailer jack # PS1401080303 that you referenced you'd want the # BD015273. This is 1-7/8 inch long and 2-1/2 inch diameter.

expert reply by: Jameson C

0

Answer 1

I went to our warehouse to provide you a few measurements of the Pro Series pipe mount swivel jack #PS1401080303. The length of the entire swivel jack in the retracted position is 26-3/4 inches. The foot plate is 3-3/4 inches wide and 7-1/2 inches…

view full answer...

Answer 2

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 4

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to…

view full answer...

Answer 5

The 1-7/8 inch width is what is rounded up to 2 inches which is a standard width for winch straps. The 14 foot length is not something we carry. I recommend the Hand Winch Strap with Safety Hook, 2" Wide x 15' Long - 4,000 lbs…

view full answer...

Answer 6

The 18.5x8.5-8 is actually an old tire size that is not used much anymore. The closest metric size to your existing tire would be 215/60-8. Your wheel most likely has a 5-on 4-1/4 inch bolt pattern (see link), you will want to make sure that the bolt…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

I spoke with my contact at Pollak and he stated that the Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket, #PK11893-11933 is the correct replacement part for the Pollak PA66-MD40 that you have.

view full answer...

Replacement Pipe Mount to Use with Pro Series Jack # PS1401080303

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching