Recommended Replacement RV Scissor Jacks

Question

Question:

I was shopping for upgraded RV scissor stabilizer jacks.

asked by: Travis M

0

Expert Reply:

The upgraded scissor stabilizer jacks that I recommend are the Leveling Scissor Jacks with Handle part # JSC-30 which have a 10,000 lb capacity and offer up to a 30" lift. They also come with an easy to use crank handle. They can be bolted or welded to the frame.

expert reply by: Conner L

0

Answer 1

The diameter of the top plate on the #JSC-30 is 9 inches. This top plate is also the mounting plate as the bottom is what touches the ground. The holes on this plate are 7-7/8 inches apart measured across.

view full answer...

Answer 2

Scissor style stabilizer jacks like the Leveling Scissor Jack Set #JSC-24 would be your best option. These were designed to stabilize camper trailers but would work great for what you are wanting. I attached a picture of what they look like in use…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer jacks. I'm…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Recommended Replacement RV Scissor Jacks

Product Page this Question was Asked From

Continue Researching