What is Minimum Diameter Hole Needed to Install Valterra Water Inlet RF911BK

Question

Question:

What is the minimum cut out hole needed for this model? Thanks.

asked by: Haston

0

Expert Reply:

The barb fitting on the backside of the Valterra Water Inlet # RF911BK starts out at 1-1/4 inch at the end and then gets a little wider towards the base at 1-3/8 inches which means that the minimum diameter hole it would fit through is 1-3/8 inch.

expert reply by: Jameson C

0

Answer 1

The Valterra #RF911BK water inlet features a barbed connection that starts out at 1-1/4 inches in diameter at the end and flares to 1-3/8 at the end right behind the inlet. It will fit a flexible hose with a 1-1/4 inch inside diameter. If…

view full answer...

Answer 2

Thank you for the photo, it was very helpful, and I can confirm that your current B&B city water inlet can be directly replaced with an option from JR Products: - White: RV City Water Inlet with Brass Check Valve - 1/2" MPT…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Wyatt, so we have a hose that was designed to be used with the #T01-0091VP with the part #W01-4180 which does have a different thread size. This is intentional so that someone doesn't use a standard garden hose that someone might attempt to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

The pin weight of a 5th wheel trailer will usually be around 20% of the trailer's gross trailer weight (GTW) rating. The only real way to find the loaded pin weight of your 5th wheel trailer would require access to a commercial scale used to…

view full answer...

Answer 10

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 11

You do not have to use a sliding 5th wheel hitch in a short bed truck. In many cases, truck beds shorter than 8 ft do not have enough clearance between the trailer and truck to execute sharp turns. This is why sliding hitches were invented. Due to…

view full answer...

Answer 12

To know if your 2017 Ford F-350 has an in-bed puck system installed you'll just need to look and see if you have four rounded attachment points (usually covered up when not in use, like in the attached picture). If you don't see these in your…

view full answer...

What is Minimum Diameter Hole Needed to Install Valterra Water Inlet RF911BK

Product Page this Question was Asked From

Continue Researching