Solution to Have 7-Way in Truck Bed and at Rear of Truck for Camper and Towing Trailer

Question

Question:

What connector do I need to hook up a truck camper and pull a trailer?

asked by: Wayne B

0

Expert Reply:

To give your truck a 7-way in the bed of your truck for the camper and have one at the rear for the trailer you'd want the part # 41157. This plugs into the 7-way at the rear of the truck and gives you another one you can install up in the bed for the camper.

expert reply by: Jameson C

0

Answer 1

We do have camper tie-downs other than the Torklift, but there are several restrictions for their use. One of the tie-downs is part #HSSF. These clamp onto the bed rails of your truck. The restrictions are the bed rail cannot exceed 5-1/2 inches…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

There is not a plug and play adapter for your Lance connector that we are aware of. Typically this is installed by the Lance dealer. A junction box/7-way plug kit like #HS381-9000 is an option you have to convert the camper to match the 7-way RV…

view full answer...

Answer 8

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 9

Thanks for the photo, that was a big help. And the answer is yes, your 2023 Ford F-350 Cab & Chassis is 100 percent compatible with the Curt 7-way: - Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector #C69CR…

view full answer...

Answer 10

Hey Chad this is a great question. So the MORryde ALLTREK part #MR89DR does offer additional vertical suspension but it does sit a little taller than the equalizers it replaces so you wouldn't have to worry about your tires hitting fenders or…

view full answer...

Answer 11

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 12

The 1-5/16" Hellwig Adjustable Big Wig Rear Anti-Sway Bars are designed for 2WD #HE97MR or 4WD #HE94FR versions of your 2021 Ford F-250. These are both designed for trucks which have a stock ride height. Hellwig does offer their 2" Lift…

view full answer...

Solution to Have 7-Way in Truck Bed and at Rear of Truck for Camper and Towing Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching