Stake Pocket Camper Tie Downs for 2003 Toyota Tundra

Question

Question:

do you sell a stake pocket camper tie down for 2003 tundra?

asked by: Perry M

0

Expert Reply:

For stake pocket tie-downs that will work in your 2003 Toyota Tundra you will want the Brophy Clamp On Camper Tie-Downs # HSSF.

These tie-downs are compatible with the turnbuckles # TDHP that you'd need to complete your camper tie down setup for your truck. This provides the connection from the tie down to the camper. I attached a review video for more info as well.

expert reply by: Jameson C

0

click to enlarge

Answer 1

For your 2016 Toyota Tundra with a 6-1/2 foot bed, I recommend looking at the Brophy Clamp On Tie-Downs - Bed Mount #HSSF. These are a universal fit that will work great on your Tundra as long as the underside of the bed rail lip is at least two…

view full answer...

Answer 2

CR Brophy, the manufacturer of the #HSSF tie downs did not test fit on the 2006 Toyota Tundra, so they can neither confirm or deny the fit. I was told that if the bed is single walled and the lip under the bed side is at least 2 inches wide, the tie…

view full answer...

Answer 3

I went out to the warehouse and pulled a Camper Hold Down, #HSSF, to measure so you could compare the measurements to your truck to determine fit. The hold down will go around a bed rail that is no wider than 5 inches. The top part of the hold down…

view full answer...

Answer 4

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 5

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

Answer 6

It sounds like the purpose of getting the air helper spring would be to counteract the 1 inch compression you're getting in your rear suspension caused by the pin weight of your 5th wheel. If that's the case, I believe that the AirLift 5000…

view full answer...

Answer 7

We have run into this quite a few times in the past, and the best option will be replacing the Lance 7-pin connector with a standard 7-way blade connector like the #PK12706. This will give you a standard 7-way connector to plug into the factory 7-way…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 10

The primary advantage of frame-mounted camper tie-downs like the TorkLift #TLF2012A and #TLF3001A, which are designed to fit your Ford F-350 if it has the 6-3/4 foot bed without a step/board underneath and a factory hitch, is the stability they…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Yes you can absolutely use the HappiJac Qwik-Load Turnbuckles for Camper Tie-Downs #LC182895 with your TorkLift tie downs.

view full answer...

Stake Pocket Camper Tie Downs for 2003 Toyota Tundra

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching