Wire Gauge Used on ThermaHeat RV Holding Tank Heater Pad

Question

Question:

I am interested in: The ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat - 18-1/4 Long x 12 Wide Item # 277-000164. What gauge is the wire and will the pad adhere to fiberglass? I believe that this work work well installed inside the lid of the fiberglass compartment containing the lithium batteries on my boat.

asked by: John N

0

Expert Reply:

The gauge wire that is used on the ThermaHeat RV holding tank pad part # 277-000164 is 14 gauge. It would adhere to fiberglass.

expert reply by: Jameson C

0

Answer 1

There are two wires coming from the ThermaHeat RV Holding Tank Heater Pad part #277-000164. There is a red wire for the 12 volt power and a white wire for the ground. This heating pad draw's 4.8 amps of power. Therefore, if you will be attaching…

view full answer...

Answer 2

The gauge wire used on the 18-1/4" x 12" Holding Tank Heater Pad #277-000164 that you referenced is 14 gauge.

view full answer...

Answer 3

The Holding Tank Heater Pad part #277-000164 is a thermostatically controlled heating pad that is designed to turn on when the water in the tank is below 45 degrees Fahrenheit and turn off when the water in the tank is about 67 degrees Fahrenheit. If…

view full answer...

Answer 4

The manufacturer for the ThermaHeat RV Holding Tank or Step Heater Pad #277-000164 recommends using 3M Hi Strength 90 spray adhesive to reattach the pad if the self-stick adhesive starts to fail. This can be purchased at your local auto parts or…

view full answer...

Answer 5

Yes, the ThermaHeat RV Holding Tank or Step Heater Pad w/ Thermostat - 18-1/4" Long x 12" Wide #277-000164 can be applied to powder coated metal surfaces. It is not uncommon for people to install these on the underside of their metal RV…

view full answer...

Answer 6

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 7

I spoke with my contact at Command regarding the LED RV Interior Light #328-K-1050Q9 referenced in your question. The LED unit has a draw of 0.26 amps. I have attached a short video demonstration for this light that you can also take a look at.

view full answer...

Answer 8

The StabiliTrak that's built into your GMC Sierra does the same thing that the Curt True Course Advanced Bluetooth Trailer Sway Control #C94VV does, so you'd have to disable the built in TSC to use it. Since they're the same thing,…

view full answer...

Answer 9

Thank you for the photos and sorry to hear about your truck! The unique design of the B&W Tow & Stow 2-Ball Mount - Compatible with GM MultiPro Tailgate #BWTS20066BMP is that angled section that meets with the shank part of the ball mount. On…

view full answer...

Answer 10

Those are some good questions, and we'll start with if the brake lights will flash during activation using the Curt True Course Advanced Bluetooth Trailer Sway Control #C94VV. The answer to that is no, they will not flash when the True Course is…

view full answer...

Answer 11

I just checked with my contact at Curt. The Curt True Course #C94VV does not have a provision for the user to adjust its sensitivity. The True Course is more for emergency maneuvers, high winds, semi trucks passing and so on. It is not necessarily…

view full answer...

Answer 12

Congrats on the new truck! You won't have to swap our your Curt Q20 Hitch but you will need to use an adapter because GM changed the puck pattern in 2020. The correct adapter is the Item #C88KR you were looking at. This will mount directly to the…

view full answer...

Wire Gauge Used on ThermaHeat RV Holding Tank Heater Pad

Product Page this Question was Asked From

Continue Researching