Mounting Bracket with Wiring for Use with Optronics Trailer Light MCL75AB

Question

Question:

I am looking to purchase some of your MCL75AB thin line amber lights. The info says I need a mounting bracket A65 B. I see that bracket doesnt have a wire to hook up to the feed. Shouldnt I need the bracket part # A 65 PB. If not , what mounting bracket do I need with a wire? Thank you

asked by: Alan R

0

Expert Reply:

The correct mounting bracket to use with the # MCL75AB would be the part # A65PB which comes with the correct and easy way to wire up the light.

expert reply by: Jameson C

0

Answer 1

You can certainly replace your existing incandescent marker/clearance lamps with LED models. LEDs have many advantages over incandescent lamps. They have a much longer life, they draw a fraction of the amperage and are brighter. The Optronics LED…

view full answer...

Answer 2

The standard square trailer roof vent size for the majority of trailers is the 14 x 14-inch size. And we do offer replacement lids, protective covers and also complete new vent assemblies. If you need just a new vent lid you can refer to the linked…

view full answer...

Answer 3

The dimensions of the screws used largely depends on your individual camper and the base of the lights. I would recommend using stainless steel self-tapping screws so that they they have a firm grip and will withstand corrosion.

view full answer...

Answer 4

For a mounting bracket for the Optronics Trailer Light #MCL75RB that you referenced you would want an Optronics Black Mounting Bracket #A65PB. How it will mount will depend on your trailer, but basically you will need to use a screw or bolt with a…

view full answer...

Answer 5

The back of the lights that go with the Black Bracket and Single Wire Plug for Thin Line Series Trailer Clearance and Side Marker Lights, #A65PB, have a recessed area over the mounting holes. Take a look at #MC65RB, and click on the third picture to…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...